valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
6. Put the hose onto the threaded hose base by turning the fitting on the end of the hose clockwise (See Figure 2). Hands tighten only. Do not over-tighten. 7. Hang the steam nozzle on the steam nozzle holder as shown in Figure 3. Figure 1 Figure 2 Figure 3 NOTE: The telescopic pole must be fully extended during steam operation to ensure smooth lining of the hose and provide a free flow of steam. 7 CAUTION: Always hang the steam nozzle on the steam nozzle holder when not in use to prevent steam from causing bodily injury or damage to surfaces. WARNING: Do not pull the hose with excessive force or damage will occur and causing steam leakage. Do not move the appliance by grasping the hose. ACCESSORY ASSEMBLY To attach fabric brush onto the steam nozzle: 1. Turn off the steamer and wait until no steam emits from the steam nozzle. 2. Align the pegs along the back of the accessory with the holes on the steam nozzle. See Figure 4. 3. Push until the brush is firm in place. Figure 4 CAUTION: Do not install the accessory while steam is emitting from the steam nozzle to avoid burns. Operating Instructions 1. Unplug the power cord and turn the switch to “OFF” position. 2. Remove the water tank, turn it upside down, and unscrew the valve cap (See Figure 5). Fill the water tank with cool water and replace the valve cap. Do not use hot water. To prolong the lifetime of your steamer, it is recommended to use distilled or de-mineralized water. Place the water tank back into the unit and make sure it is sitting properly and securely in the 8 cavity. (See Figure 6) Do not let the steamer operate with a dry water tank, or the damage to the unit could occur. 3. Plug the unit into an outlet. 4. Turn on the switch. Verify that the light on the switch is illuminated. Steam should start flowing from the nozzle in approximately 45 seconds. 5. When finishing with the steaming session place the switch to the “OFF” position and remove the plug from the outlet. Figure 5 Figure 6 PRESSING WITH STEAM 1. To steam a garment, place it on a clean, rust-free clothes hanger and place the hanger on the clothes hanger hook. 2. Grasp the handle and place the steam nozzle at the bottom of the garment. Steam will rise along the inside and outside of the fabric, removing the wrinkles. Slowly slide the nozzle vertically from the bottom to the top of the garment (See Figure 7). Do not allow kinks to form in the hose at any time. 3. Remove the nozzle from bottom to top on the garment and smooth the fabric with your free hand. 4. Repeat steps 2 and 3 as necessary until the fabric is wrinkle free. 5. Curtains and draperies can be steamed while still hanging (See Figure 8). 6. Heavier fabrics may require repeated steaming. 7. To remove stubborn wrinkles, the fabric brush may also be used. Figure 7 Figure 8 9 CAUTION: Be careful when handling garments on the clothes hanger hook. Pulling on the garment with too much force may cause the unit to tip. Cleaning and Maintenance COMPLETELY CLEAN AND DRY ALL PARTS AFTER EVERY USE. Be sure to unplug the appliance before cleaning. To protect against electrical shock, do not immerse cord, plug or unit in water or other liquid. Never use harsh abrasives, caustic cleaners on the interior surface. Wipe dry with clean cloth. For stubborn stains, use a nylon or plastic scouring pad or a powdered, non-abrasive cleaner. Dry thoroughly before closing. To clean the exterior finish, simply wipe with a clean damp, cloth. Re-fit the bowl after cleaning. This keeps the mechanism underneath covered. For all other parts, wash by hands and dry thoroughly. It is recommended to follow these instructions at least once per week: 1. Turn the switch to “OFF” position. 2. Unplug the unit from the power outlet. 3. Allow the steamer to cool for at least 30 minutes. 4. Remove the hose and shorten the telescopic pole, then set them aside. 5. Remove and drain the water tank. Rinse the water tank with fresh water and drain completely. Place the water fill tank back on the water reservoir. 6. Drain the steamer by removing the drain plug and emptying the contents. 7. Flush the u nit by filling the water reservoir and the hose connector with fresh water and draining completely. Replace the drain plug. 8. Wrap the hose around the telescopic pole one time. Place the steam nozzle on the steam nozzle holder. 9. Store in a cool, dry place. 10 REMOVING THE MINERAL BUILD-UP One common problem with steamer is mineral build-up caused by a high mineral in many municipal water suppliers. Mineral residue inside of the internal pipes and heater can cause intermittent steaming or, in some cases, no steaming at all. According to the water quality in different regions, it is advised to remove the mineral build-up after using 15-30 days. Please take a reference of the following procedures. The procedures below can be used to reduce mineral build-up. If you are unable to use de-mineralized or distilled water, it is recommended to follow these procedures on a monthly...