Produttore : Oliso
File Size : 985.73 kb
File Nome : 886fd2fc-58eb-41ba-9d8b-b35613195788.pdf
|
Facilità d'uso
Smarter. Simpler. IMPORTANT SAFETY INSTRUCTIONS When using your iron, basic safety precautions should always be followed, including the following: Read all instructions before using this product. 1 ) Use iron only for its intended use. 2 ) To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3 ) The iron should always be turned to “Off” before plugging or unplugging from the outlet. Never yank cord to disconnect from the outlet; instead, grasp plug and pull to disconnect. 4 ) Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. 5 ) Always disconnect iron from electrical outlet when filling with water or emptying and when not in use. 6 ) Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to a qualified serviceman for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used. 7 ) Do not allow children to use iron. Close supervision is necessary for any appliance being used near children. Do not leave iron unattended while connected or on an ironing board. 8 ) Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir. 9 ) If the LED flashes orange (not red or green), the iron is not operating normally. Disconnect from the power supply and have the iron serviced by qualified service personnel. SPECIAL INSTRUCTIONS 1 ) This is a 1440 watt appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 2 ) If an extension cord is absolutely necessary, a 12 ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. save these instructions Welcome Thank you for purchasing the Oliso™ Iron, the only iron with the patented AUTO-LIFT SYSTEM™. You’re just a few steps away from a new safer, easier way of ironing. Follow the instructions in this manual to learn about your new iron’s features and care. We hope you enjoy your Oliso™ Iron. Smart. Simple. Delightful. 3 simple steps to start 12 FILL SET UP Open the Flip Funnel™ and add water to the tank with the fill cup or directly from a faucet. Plug in, then choose a fabric setting. IRON Enjoy your Oliso™ iron If you would like to learn more about your iron’s unique features, please read on. When the green light stops blinking and is constantly lit, the iron is ready for use. Touch the handle and begin. getting to know your Oliso™ iron Status Light Steam Button Spray Button Touch-activated handle Steam Selector Auto-Lift™ on/off switch Electronic Fabric Selector Drain Spout Flip Funnel™ Water Tank Spray Nozzle Detailer Soleplate - non-stick (TG-800) - stainless steel (TG-1000) Lifters Auto-Lift System™ To operate, place the iron right side up on a flat surface. Plug the iron into an outlet and make sure the Auto-Lift switch is in the on ( ) position. Touch the iron handle and the iron will sense your hand and lower. Let go and the iron’s Lifters will automatically raise the iron above fabric. overriding the Auto-Lift system™ If you wish to turn off the Auto-Lift system, move the switch on the back of the iron to the off ( ) position. Your iron will now operate like a standard iron. If the iron is left in the horizontal position without being touched for more than 30 seconds, the Auto-Lift system will automatically raise the iron. This will prevent the iron from scorching or burning. Touch the iron handle, and the iron will lower. You can restore Auto-Lift by returning the switch to the on ( ) position. water tank Alternatively, fill directly from a faucet holding the iron horizontally. Do not fill the tank past the MAX fill line on the side of the iron. Close the port when done. Before filling, slide the steam selector to off ( ). Make sure the iron is unplugged. If you need to add water during ironing, unplug the iron and repeat the above steps. After filling, make sure the iron is fully reheated before ironing. Open the Flip Funnel™. Leave the iron in a horizontal position and fill using the included fill cup. Two fill cups equal the maximum capacity of the water tank. water recommendations This iron is designed to be used with regular tap water. If your water is over 12 grams of hardness we recommend using either inexpensive bottled spring water or mixing half tap water with half distilled water. Never use 100% distilled water as this can cause the iron to spit and leak. fabric selector steam ok temperature is too low for steam Turn the fabric selector to select a fabric setting. To use constant steam or steam burst, the temperature must be set to the wool, cotton, or linen range. fabric selector red flashing green green flashing red off heating or cooling at set ...
Questo manuale è adatto anche per i modelli :Ferri - TG-800 (985.73 kb)