valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
3. To protect against risk of electrical shock, do not immerse the iron in water or other liquids. Always turn the iron to “OFF” before plugging in or unplugging from outlet. 4. Never yank cord to disconnect from outlet. Grasp plug and pull to disconnect. 5. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. 6. Always disconnect iron from electrical outlet when filling with water, emptying, or when not in use. 7. Do not operate iron with a damaged cord, or after the iron has been dropped or damaged in any manner. To avoid the risk of electric shock, do not disassemble the iron. Return the iron to EURO-PRO Operating LLCfor examination and repair. Incorrect reassembly can cause the TROUBLESHOOTING PROBLEMPOSSIBLE REASONS & SOLUTIONSIron does not heatThermostat ready lightgoes On and OffSome odor or small particles come out of steam vents of new ironIron does not steamWater droplets comingfrom steam vents• Iron should be plugged into a 120V AC electrical outlet only. Make sure that the plug is securely in the socket. • Temperature setting too low. Turn to higher setting. • This is normal. The light goes On and Off as the thermostat is switching the heating element On and Off to maintain the selected temperature. • This is normal. Follow instructions for first use and allow iron to steam through 2- 3 fillings & press the steam burst button occasionally to eliminate small white particles. • Water tank may be empty or water level is very low. Add water. • Make sure that the temperature control dial and the variable steam control are correctly set. Formaximum steam, (setting ‘Max’ on steam control), temperature control dial should be set on ‘• •• ’. • Adjustable steam control is set on “0”. Always allow the iron to reach the selected temperature with the adjustable steam control setting at ‘0’. Make sure the temperature control dial is set in the correct steam area, e.g. ‘•’, and the steam control is noton ‘0’. For more steam, turn temperature dial to higher setting, e.g. ‘••• ’, and the steam control to ‘Max’. • If temperature setting and steam control setting arecorrect and there is no steam, gentlytap the soleplate on the ironing board a few times. Movethe variable steam control from ‘0’ to ‘Max’ a fewtimes. • Iron may not be hot enough. Set thermostat to the‘Max’ position. Always allow iron sufficient time toheat up (thermostat light goes off) before activating the variable steam control. • Overuse of steam burst. Allow more time betweeneach burst. • Iron may have been overfilled. Turn iron off,emptywater and follow instructions for filling. • Steam performance be low if iron requires seasoning. To season, use regular tap water for 1or 2 tanks until steam improves. 10 ADDITIONAL IMPORTANT SAFEGUARDS 2 1. Do not rest iron on soleplate. 2. Never use or rest iron on an unstable surface. 3. While the iron is hot, never set iron on an unprotected surface - even if it is on its heel rest. 4. WARNING! TO PREVENT ELECTRIC SHOCK OR OTHER INJURY, before filling the iron with water, make sure that the plug is removed from the outlet. 5. CAUTION: Never fill the iron with fabric conditioner, starches or any other solution, as these will damage the steam mechanism. Do not use contaminated water. 6. WARNING! TO AVOID FIRE, never leave iron unattended while it is plugged in. 7. WARNING! TO PREVENT ELECTRIC SHOCK, never immerse the iron in water or other liquid. 8. WARNING! TO PREVENT ELECTRIC SHOCK, never use the iron in a location where it can fall or be pulled into water or any other liquid. If the iron falls into water or any other liquid, unplug it immediately. DO NOT reach into the water or liquid. 9. CAUTION: Never use scouring pads, abrasive or chemical cleaners, or solvents to clean the exterior or soleplate of your iron. Doing so will scratch and/ or damage the surface. 10. WARNING! DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur. 11. Never store your iron face down, even the smallest amount of moisture will cause the soleplate to corrode and stain. 12. DANGER! Never use the iron if it is damaged or dropped. Using the iron when it is damaged could create the risks of fire, electric shock, injury or death. DIRECTIONSON LABELFABRICTEMP. CONTROLSTEAMCONTROLBURST OFSTEAMSPRAYPlease note that on the label means ‘THIS ARTICLE CANNOT BE IRONED!” COTTONLINENSYNTHETIC FIBERS, e.g.acrylic, nylonpolyesterSILKWOOLMIN• •• •• • MAX0MAXIMUMSTEAMMINIMUMSTEAM9IRONING CHART NOTE: Before starting to iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an inside seam. To select iron temperature, align temperature selected on dial with the indicator on the water tank. GETTING TO KNOW YOUR RETRACTABLE CORD IRON Before using your EURO-PRO Select Retractable Cord Iron, remove any labels, stickers or tags that may be attached to the body or soleplate of the iron. When turned on for the first time,...