valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Do not use contaminated water. 14. CAUTION! TO AVOID FIRE, never leave iron unattended while it is plugged in. 15. CAUTION! TO PREVENT ELECTRIC SHOCK, never use the iron in a location where it can fall or be pulled into water or another liquid. If the iron falls into water or other liquid, unplug it immediately. DO NOT reach into the water or liquid. 16. WARNING: Never use scouring pads, abrasive or chemical cleaners, or solvents to clean the exterior or soleplate of your iron. Doing so will scratch and/ or damage the surface. 17. CAUTION! DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur. 18. Always store your iron standing upright, not on the soleplate. If stored face down, even the smallest amount of moisture will cause the soleplate to corrode and stain. 19. This appliance is for household use only. PROBLEMPOSSIBLE REASONS & SOLUTIONSIron does not heatSome odor or small particles come out of steam vents of new ironIron does not steamWater droplets comingfrom steam vents• Iron should be plugged into a 120V AC electrical outlet only. Make sure that the plug is securely in the socket. • Temperature setting too low. Turn to higher setting. • This is normal. Follow instructions for first use and allow iron to steam through 2- 3 fillings & press the steam burst button occasionally to eliminate small white particles. • Water tank may be empty or water level is very low. Add water. • Make sure that the fabric/temperature setting and the variable steam control are correctly set. Formaximum steam, (setting ‘Max’ on steam control), temperature setting should be set on ‘• •• ’. • variable steam control dial is set on “0”. Always allow the iron to reach the selected temperature with the variable steam control setting at ‘0’. Make sure the temperature setting is set in the correct steam area, e.g. ‘•’, and the steam control is noton ‘0’. For more steam, turn temperature dial to higher setting, e.g. ‘••• ’, and the steam control to ‘Max’. • If temperature setting and steam control setting arecorrect and there is no steam, gentlytap the soleplate on the ironing board a few times. Movethe variable steam control from ‘0’ to ‘Max’ a fewtimes. • Iron may not be hot enough. Set thermostat to the‘Max’ position. Always allow iron sufficient time toheat up before activating the variable steam control. • Overuse of steam burst. Allow more time betweeneach burst. • Iron may have been overfilled. Turn iron off,emptywater and follow instructions for filling. • Steam performance may be low if iron requires seasoning. To season, use regular tap water for 1or 2 tanks until steam performance improves. GETTING TO KNOW YOUR INTELLIGENT ELECTRONIC IRON Before using your Intelligent Electronic Iron, remove any labels, stickers or tags that may be attached to the body or soleplate of the iron. When turned on for the first time, your new iron may emit an odor for up to 10 minutes. This is due to the initial heating of the materials used in making the iron. 1. Electronic Temperature Control 2. Display Panel 3. Atomizer Spray Button 4. Burst of Steam/X-Tended Steam Burst Button 5. variable steam control 6. Water Inlet Door 7. Spray Nozzle 8. Water Level Window 9. Stainless Steel Soleplate 10. Handle 11. Auto-Off Light 12. Power Light 13. Fabric & Steam Settings 14. Temperature Indicators 15. Water Flask 2 9 IRONING CHART NOTE: Always refer to the garment care tag for ironing instructions. Before starting to iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an inside seam. To select iron temperature, align temperature selected on dial with the indicator on the water tank. The odor is safe and should not reoccur after initial heating. Also, before ironing with steam for the first time, allow iron to heat, hold in a horizontal position and hit the burst of steam button several times. The iron may emit some small particles from the steam holes. This is normal and will clear after pressing the burst of steam button several times.12111314Display Panel DIRECTIONSON LABELFABRICLED DISPLAY PANELSTEAMCONTROLBURST OFSTEAMSPRAYPlease note that on the label means ‘THIS ARTICLE CANNOT BE IRONED!” COTTONLINENSYNTHETIC FIBERS, e.g.acrylic, nylonpolyesterSILKWOOLMIN• •• •• • MAX0MAXIMUMSTEAMMINIMUMSTEAM FEATURES OF THE INTELLIGENT ELECTRONIC IRON 3 1. BURST OF STEAM /X-TENDEDTMSTEAM BURST The X-TendedTMSteam Burst provides continuous, powerful steam performance. Can be used vertically as well as horizontally. The Burst of Steam provides extra, sudden blasts of steam which aid in removing stubborn wrinkles from fabrics such as denim, cotton or linen. 6. LED DISPLAY PANEL Displays the fabric and the temperature settings. 2. ATOMIZERSPRAY BUTTON Pressing this Button provides a defined jet of spray which gently moistens fabric. 7. WATER FILLING INLET The cover prevents dust and foreign matter from entering the water tank. It also stops any water from sp...