Log:
valutazioni - 1, GPA: 3 ( )

Istruzioni per l'uso Hotpoint-Ariston, Modello KEM 645 D C

Produttore : Hotpoint-Ariston
File Size : 2.74 mb
File Nome : Hotpoint-Ariston-KEM_645_D_C-KEM_645_D_X-KEM_646_D_C-KRM_640_C-KRM_640_X-KRM_641_D_X-KRM_630_C-Pdf-Rus.Pdf
Lingua di insegnamento: ruplitenesfrdenlpt
Vai a scaricare



Facilità d'uso


Connect the wires in accordance with the instructions given in the following table and diagrams: Voltage and mains frequency 220-240V 1+N ~ 50/60 Hz Electrical cable Wire connection _ : yellow/green N: the two blue wires together L: brown and black together Other types of connection If the mains supply corresponds with one of the following: Voltage and mains frequency • 400V - 2+N ~ 50/60 Hz • 220-240V 3 ~ 50/60 Hz • 400V - 2+2N ~ 50/60 Hz Separate the wires and connect them in accordance with the instructions given in the following table and diagrams: Voltage and mains frequency 400V - 2+N ~ 50/60 Hz 220-240V 3 ~ 50/60 Hz 400V - 2+2N ~ 50/60 Hz Electrical cable Wire connection : yellow/green; N: the two blue wires together L1: black L2: brown -=!=■ : yellow/green; N1: blue N2: blue L1 : black L2: brown GB ! The electrical connection for the hob and for any built-in oven must be carried out separately, both for safety purposes and to make extracting the oven easier. On the lower part of the appliance there is a connection box for the different types of electricity supply (the picture is only an indication and is not an exact representation of the purchased model). If the mains supply corresponds with one of the following: Voltage and mains frequency • 400V 3 - N ~ 50/60 Hz proceed as follows: ! The cable provided is not suitable for the following types of installation. 1. Use a suitable supply cable, H05RR-F or higher, with the right dimensions (cable cross section: 25 mm). 2. To open the terminal board, use a screwdriver as a lever under the side tabs of the cover ( see Terminal board picture). Terminal board UNDERSIDE OF HOB 19 3. Loosen the cable clamp screw and the terminal board screws in accordance with the type of connection required and position the connection supports as shown in the following table and diagrams. 4. Position the wires in accordance with the information given in the following table and diagrams and connect the appliance by tightening all the screws for the springs as much as possible. Voltage and mains frequency Electrical connections Terminal board 400V 3-N ~ 50/60 Hz T T T i—J ± Three-phase 400 5. Secure the power supply cable by fastening the cable clamp screw, then put the cover back on. Three-phase 400 Phase u-bolt Phase Phase Neutral Earth connection support Connecting the electricity supply cable to the mains If the appliance is being connected directly to the electricity mains an omnipolar switch must be installed with a minimum opening of 3 mm between contacts. ! The installer must ensure that the correct electrical connection has been made and that it is fully compliant with safety regulations. Before connecting the appliance to the power supply, make sure that: • The appliance is earthed and the plug is compliant with the law. • The socket can withstand the maximum power of the appliance, which is indicated on the data plate located on the appliance itself. • Th...

Questo manuale è adatto anche per i modelli :
Piani di cottura - KEM 645 D X (2.74 mb)
Piani di cottura - KEM 646 D C (2.74 mb)
Piani di cottura - KRM 630 C (2.74 mb)
Piani di cottura - KRM 640 C (2.74 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie