valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. if an external electrical source is used, the appliance, when installed, must be electrically grounded in accordance with local codes or in their absence of local codes with the National Electric Code ANSi/NFPA No. 701987 or latest edition. Check all code rules and regulations for connecting the cooktop to be certain the installation conforms with all local, municipal and state codes as well as local utility regulations. Note: All hookups and adjustment shall be performed by qualified technicians. Situations where appliance power cord will be disconnected frequently. Do not use an adaptor plug in these situations because disconnecting of the power cord places undue strain on the adaptor and leads to eventual failure of the adaptor terminal. the customer should have 2-prong wall receptacle replaced by a 3-prong (grounding) receptacle by a qualified electrician before using the appliance. Disconnect electrical supply cord from wall receptacle before servicing cooktop. 8. Check Operation Refer to the Use and Care Guide packaged with the cooktop for operating instructions and for care and cleaning of your cooktop. Do not touch the burners. they may be hot enough to cause burns. 1. Check the Igniters (some models) Operation of electric igniters should be checked after cooktop and supply line connectors have been carefully checked for leaks and the cooktop has been connected to electric power. to check for proper lighting, push in and turn a burner valve to the LitE position. the burner valve should light when gas is available to burner. Once the burner lights, it should be turned out of the LitE position. try each valve separately until all burners have been checked out. The burners can be lit manually during an electrical power outage. To light a burner, hold a lit match to the burner head, then slowly turn the Surface Control knob to LITE. Use caution when lighting burners manually. Surface burner in use when an electrical power failure occurs will continue to operate normally. the surface burners on models equipped with pilots can operate during an electrical power outage. Failure to comply with the above could result in a serious shock hazard. 9 GAS COOKTOP INSTALLATION INSTRUCTIONS GAS COOKTOP INSTALLATION INSTRUCTIONS 2. Adjust the "LO" or "SIMMER" Setting of Surface Burner Valves (30" Cooktops Only) (see Figure 20) Push in and turn each control knob to the "LO" (or "SiMMER") setting. the "LO" setting of each burner has been set at the factory to the lowest setting available to provide reliable reignition of the burner. if it does not stay lit on the "LO" setting, check the hollow Valve System Figure 20 setting as follows. A. Allow cooktop to cool to room temperature. B. Light all burners by turning each control knob to LitE until burners ignite, and then set them at "hi". C. Quickly turn the knob to the LOWESt POSitiON. D. if burner goes out, readjust valve as follows: Remove the surface burner control knob, insert a thin-bladed screw driver into the hollow valve stem and engage the slotted screw inside. Flame size can be increased or decreased with the turn of the screw. Adjust flame until you can quickly turn knob from hi to LOWESt POSitiON without extinguishing the flame. Flame should be as small as possible and stable without going out. E. if you need to adjust another burner, repeat the steps from A to D above until all burners operate properly. When All Hookups are Complete Make sure all controls are left in the OFF position. Make sure the flow of combustion and ventilation air to the cooktop is unobstructed. Model and Serial Number Location the serial plate is located into the burner box near the burner support or under the burner box. When ordering parts for or making inquires about your range, always be sure to include the model and serial numbers and a lot number or letter from the serial plate of your cooktop. Your serial plate also tells you the rating of the burners, the type of fuel and the pressure the cooktop was adjusted for when it left the factory. Improper installation adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information consult a qualified installer, service agency, manufacturer (dealer) or the gas supplier. Stepping, leaning or sitting on these cooktops can result in serious injuries and also cause damage to the cooktop. Be sure to keep appliance clear of combustible materials, gasoline and other flammable vapors and liquids. Before You Call for Service Read the Avoid Service Checklist and operating instructions in your Use and Care Guide. Check to make sure the house fuse or circuit breaker for your cooktop are not blown or open. Attention Home Owners Should a replacement part be needed proceed as follows: iMPORtANt: 1. Copy the complete model, lot and serial number from the serial number plate. 2. ...
Questo manuale è adatto anche per i modelli :Piani di cottura - 30 (515.33 kb)