valutazioni - 1, GPA: 5 ( )

Produttore : DCS File Size : 97.27 kb File Nome : 712201EN.pdf Lingua di insegnamento:

A minimum distance of 100 mm. must be left between the side edges of the hob and any adjacent cabinets or walls. The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 420 mm. If it is fitted below 420 mm. a space of 50 mm. must be allowed from the edges of the hob. The minimum distance combustible material can be fitted directly above the hob is 700 mm. 650 mm 420 mm 420 mm 100 mm 50 mm 50 mm 55 mm 600 mm 700 mm 420 mm 100 mm 420 mm50 mm 55 mm 50 mm CLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE FO 0813FO 0812 700 mm Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Cut Out Size The dimensions of the cut-out are given in the diagram. 550470 580500 55 min. FO 2109 Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. ON/OFF SWITCH FLEX OUTLET FO 0763 1 ON/OFF SWITCH 2 FLEX OUTLET FO 0764 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. 30 20 min60 a b FO 1013 3 Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. Seal 1) Place the sealing gasket all around the + edge of the cut out. 2) Place the hob into the cut out and secure it by means of the relevant fixing clamps and screws, as shown in the diagram. 3) Remove the excess seal The edge of the hob forms a double seal which prevents the ingress of liquids. FO 0199 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate. The rating plate is located on the bottom of the hob. A copy is attached on the back cover of this book. The hob is supplied without supply cord. A 3 core flexible supply cord must be fitted, in accordance with the specification given in the relevant tables. 1) Remove the mains terminal cover . plate from the underside of the hob, to expose the mains terminal block. 2) Loosen the two cable clamp screws and lift the top section of the clamp enough to allow the cable to be passed through. 3) Connect the red (live) wire to the terminal which is marked with the number 1. FO 0488 4) Connect the black (neutral) wire to the terminal which is marked with the number 4. 5) After fitting a green or yellow/green sleeve over the bare copper wire (earth wire), connect the exposed end to the terminal which is marked with the earth symbol or with the number 5. NOTE: The earth wire should be about 2 cm. longer than the live and neutral wires. 6) Secure the cable by means of the clamp screws and refit the terminal block cover. Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg. C. Supply Cable Specifications For Uk use only Connection Min. size Cable / flex Fuse via Cable/flex type • Cooker 6 mm2 PVC/PVC 30 A Control twin and Circuit earth For Europe use only Min. size Cable/flex Cable / flex type Fuse 2.5 mm2 H05 RR-F 30 A Wiring diagram 1 43 2 1 4 3 1 2 5 P2 P1 P3 1 43 2 1 4 3 1 2 5 P2 P1 P3 2 43 2 1 4 3 3 4 1 2 5 P2 P1 P3 43 2 1 4 3 1 2 5 P2 P1 P3 PLATE O 180 O 180 R O 145 R O 145 L 3 L 4 N ...

Scarica la tua

Per scaricare, digitare 2 cifre :