valutazioni - 3, GPA: 4 ( )

Produttore : GE File Size : 2.32 mb File Nome : Lingua di insegnamento:

Control Panel Door Press to open and close the door. NOTE: The remote control (on some models) will work with the control panel door open or closed. Normal operating sounds. ¦ You may hear a pinging noise caused by water being picked up and thrown against the condenser on rainy days or when the humidity is high. This design feature helps remove moisture and improve efficiency. ¦ You may hear the thermostat click when the compressor cycles on and off. ¦ Water will collect in the base pan during high humidity or on rainy days. The water may overflow and drip from the outdoor side of the unit. ¦ The fan may run even when the compressor does not. 7 Air Filter The air filter behind the front grille should be checked and cleaned at least every 30 days or more often if necessary. To remove: Open the inlet grille upward by pulling out the bottom of the inlet grille. Using the tab, pull up slightly on the filter to release it and pull it down. Clean the filter with warm, soapy water. Rinse and let the filter dry before replacing it. Do not clean the filter in a dishwasher. CAUTION:DO NOT operate the air conditioner without a filter because dirt and lint will clog it and reduce performance. 2 1 Outdoor Coils The coils on the outdoor side of the air conditioner should be checked regularly. If they are clogged with dirt or soot, they may be professionally cleaned. Grille Frame Removal (if necessary for coil cleaning) Remove the air filter. See the Air Filter section above. If present, remove the grille frame attachment screw. Grasp the lower corners of the grille frame while pressing in on the case side tabs with your finger tips. Pull out to release and lift it up. NOTE: Do not pull the bottom edge toward you more than 3. or you may damage the tabs of the grille. Grille and Case Turn the air conditioner off and remove the plug from the wall outlet before cleaning. To clean, use water and a mild detergent. Do not use bleach or abrasives. Care and cleaning of the air conditioner. How to Insert the Batteries in the Remote Control Remove the battery cover by sliding it according to the arrow direction. Insert new batteries, making sure that the (+) and (–) of battery are installed correctly. Reattach the cover by sliding it back into position. NOTES: ¦ Use 2 “AAA” (1.5 volt) alkaline batteries. Do not use rechargeable batteries. ¦ Remove the batteries from the remote control if 3 the system is not going to be used for a long time. 2 1 8 Safety Instructions Operating Care and Cleaning Instructions Installation Consumer Support Troubleshooting Tips Instructions Installation Instructions Air Conditioner Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: ge.com In Canada, call 1.800.561.3344 or visit BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT — Save these instructions for local inspector’s use. • IMPORTANT — Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions for future reference. • Skill level – Installation of this appliance requires basic mechanical skills. • Completion time – Approximately 1 hour • We recommend that two people install this product. • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty. • You MUST use all supplied parts and use proper installation procedures as described in these instructions when installing this air conditioner. CAUTION: Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Do not change the plug on the power cord of this air conditioner. Aluminum house wiring may present special problems—consult a qualified electrician. TOOLS YOU WILL NEED Phillips head screwdriver Ruler or tape measure Pencil Level Scissors or knife Flat-blade screwdriver Adjustable wrench ELECTRICAL REQUIREMENTS The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button Some models require 230/208-volt a.c., protected with a time delay fuse or circuit breaker. These models should be installed on their own single branch circuit for a properly grounded 3-prong wall outlet. best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires. 9 the outlet. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician. and then the RESET button while plugged into Type A (6) V-support (2) Window locking bracket (2)...

Scarica la tua

Per scaricare, digitare 2 cifre :