valutazioni - 4, GPA: 4.8
(
)
)
|
Facilità d'uso
ribbon located under the ceramic glass surface to To the right (clockwise) starts with heat setting provide the heat for cooking.These radiant elements 1 (low). will cycle on and off by design (see Temperature To the left (counterclockwise) starts with heat Limiters, below.) There are 9 heat setting positions setting 9 (high). from 9 (high) to 1 (low) and a special setting for keep Turn the dial until the desired heat setting is warm. displayed. Dual Element Setting the Controls (single element) The dual element consists of two radiant ribbon 1. Follow steps 1, 2 and 4 above. elements within the same heating area. Either the small Changing Heat Setting While Cooking inner element or both the inner and outer elements 1. Touch element pad for element desired. Display may be selected for use, depending on the size of will show 0. cookware. (See page 7.) 2. Turn dial. The first turn of the mTwisT dial will Temperature Limiters display the current cook setting. Each UltraSpeed heating element has its own sensor to protect the glass cooking surface from extreme 3.Turn dial left or right to new cook setting. The new high temperatures. The limiters will operate cook setting is displayed. automatically by cycling the element on and off Change Pot Size when Cooking (for dual only) regardless of the cook setting. See Pot Sizing (Page 6 ). Although cycling is normal, any one of the following To Turn Off One Surface Element conditions can activate the limiter and cause it to cycle on and off more than usual: 1. Touch element pad for desired element. • The base of the pan is not making full contact 2. Display shows 0. After 5 seconds the element with the heating surface (due to a warped or shuts off. uneven base). Or • The pan is too small for the size of the element. touch element pad twice. • The pan has boiled dry. Or • The material or shape of the pan is slow to touch element pad once. After five seconds, transfer the heat. the element turns off. Setting the Controls (dual element) To Turn Off All Elements at the Same Time 1. Place pan on element. 1. Touch POWER OFF pad. 2. Touch element pad for desired element. Display Or will show a 0. Remove mTwisT dial from cooktop. Once removed, the cooktop controls are locked. Replace 3.Touch POT SIZING pad. Control defaults to large mTwisT dial then touch and hold PANEL LOCK pad size (inner and outer) element. Touch the POT for three seconds to unlock control. SIZING element pad again for smaller element. Touching the POT SIZING pad repeatedly alternates the element size.The dual element light comes on above element pad when using large element. PAGE 5 NES Cooktop Use and Care Manual Cooktop Operating Instructions Setting the Controls Operation Without mTwisT Dial The cooktop can be operated without the mTwisT dial. Change Pot Size - (for dual elements only) 1.Turn off Panel Lock (see below). 1. Select element pad for desired element. 2.Touch element pad for desired element. Display shows 0. 2.Touch Pot Sizing pad for desired pad. 3. Choose the POT SIZING pad (if using dual element). 3.Touch element pad until desired heat setting is displayed. 4.Touch element pad repeatedly until desired heat settting is displayed. Change Heat Setting Turn Off Element 1.Touch element pad. 2.Touch element pad until 0 is displayed. 1. Select element pad for desired element. Or 2. Each touch of the element pad changes setting. Continue touching repeadedly until desired heat setting is displayed. for several elements, select POWER OFF pad. Cooktop Function Pads Power Off Turns off all elements at the same time.The indicator light above the POWER OFF pad is lit when at least one element is on.The light will turn off when the POWER OFF pad is touched or all elements are turned off. Panel Lock The panel lock is selected to prevent the cooktop from being turned on, such as for cleaning. The elements will not function when turned on. 2.Touch POT SIZING pad to change element size chosen, element turns off. 3.Turn mTwisT dial to desired heat setting. Keep Warm Each element has a keep warm setting to keep hot, cooked foods at serving temperatures. To set Keep Warm feature: Setting Panel Lock 1.Touch element pad for desired element. 1.Touch and hold PANEL LOCK pad for three seconds.A light above the pad stays lit when the panel is locked. 2. Touch KEEP WARM pad. L is displayed above selected element and element comes on. 2. To unlock Touch the PANEL LOCK pad and hold for three seconds. The light above the pad will disappear. The cooktop cannot be locked when a surface element is operating. It is recommended to lock the cooktop before cleaning. Pot Sizing Use this pad to choose the pot size on dual elements. 1.Touch element pad for dual element. Control defaults to larger element. Dual element light comes on above element pad indicating large size is selected. Keep Warm Guidelines Use pans/utensils with flat bases. Plates and casseroles with shallow ridges around the base can be used provided they are made ...
Questo manuale è adatto anche per i modelli :Piani di cottura - NES 730 UC (541.13 kb)