valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
On the furniture into which the appliance is to be installed, the plastic coating and/or veneer must have been treated with a heat-resistant adhesive, otherwise it may become distorted or peel off, especially on the narrow sides. The rough edges of the cut-out must be sealed using a watertight material. Prior to connection of the appliance, it must be checked that the appliance specifications comply with local connection requirements (gas type and pressure). Please also check for any special regulations of your local supply company. The specifications of this appliance are listed on the rating plates which are located on the underside of the gas hob. This appliance is not to be connected to the exhaust air outlet. It must be installed and connected according to the currently effective installation conditions. Particular care must be taken to provide suitable means of ventilation. Installation (for the installer) Picture 1 Picture 2 Installation must be made by a kitchen installation expert. Note: If you intend to have the gas hob welded into a stainless steel worktop, for safety reasons and in order to fully maintain the requirements of your Siemens warranty, we recommend that this type of installation be done solely through our designated partner: Bautek. (Address available on request). IMPORTANT!!! The countertop must have a thickness of 30 mm and a maximum of 40 mm. Do not use liquid silicone to glue the hob to the countertop. The furniture below the countertop should have an opening for passage of the gas pipe and electric wires measuring at least 50x50 mm. Any eventual cabinet, resting on the worktop, at any of the two sides of the hob, and the upstand on the back of the hob, each must be at least 50 mm from the edge of the hob itself. In case of elements sold complete with cabinet, the instructions for installation of the cooker hob are provided in the manual for the cabinet. Apply the sealing gasket along the edge of the opening taking care to overlap the joints (picture 1). Fit hook B in angle iron A welded on the unit (picture 2) taking care to block it in the holes provided, depending on the thickness of the countertop (30 mm, max. 40 mm), picture 3. Turn tab C and position it under the countertop, then tighten screw D. Trim, if necessary, the part of the gasket extending beyond the cooker hob. Picture 3 Electrical connection Prior to connection check the voltage and total output on the technical label affixed to the appliance. It is obligatory that this appliance be earthed. When connecting the appliance, ensure the earth wire is connected first and that all wires are connected to the correct terminals. If a direct connection to the mains is required, it is necessary to install a device that ensures an omnipolar disconnection from the mains, with an opening distance of the contacts such as to ensure the complete disconnection in the conditions foreseen by the category of overvoltage III, as per the installation’s regulation. This is not the case if the connection is by means of a plug, provided the user has easy access to the plug itself. Fuse rating: 3 Amp. When connecting the appliance please ensure that the earthing wire is properly connected. In the event of an accident due to the fact that the appliance is not earthed, or that the earthing is faulty, we do not accept any form of responsibility. The type of cable connecting the appliance to the electricity supply must be H05RR-F3 G 0.75. In the event that the connecting cable must be replaced due to damage only this type of cable should be used. This should only be carried out by one of our after-sales service technicians. CE: This appliance complies with the following EU directives: -72/23/EEC - Low Voltage Directive -89/336/EEC - EMC Directive -90/396/EEC - Directive on Gas Appliances Gas connection (for the fitter) The gas supply system must comply with the local standards in the country in effect. Attach the elbow coupling to the appliance gas supply, using the seal provided. Your hob is pre-mounted with the connection ISO 7-1. In order to change the elbow coupling (see picture 4) Picture 4 In compliance with the currently effective regulations, the hob must be connected to the gas pipe with a stop valve. This valve must be easily accessible at all times. After connecting the unit to the gas mains always check the seal of the connection using a solution of soapy water. Never check the seal using a flame. Using flexible pipes: • do not allow the pipes to be constricted or crushed; • the pipes must not be subjected to traction or twisting forces; • do not allow the pipes to come into contact with cutting or sharp edges, etc... • do not allow any gas connecting pipe and/or any electric connecting wire to come into contact with the bottom of the hob; make sure that the entire length of the pipes and/or electric connecting wire is available for inspection. Particular care must be taken to ensure leak proof connection. The maximum permissible l...