|
Facilità d'uso
Please note that proof of purchase is required for in-guarantee service calls. Help us to help you Please determine your type of enquiry before writing or telephoning. When you contact us we need to know: • Your name • Clear and concise details of the fault • Address and post code • Name and model of the appliance* • Telephone number • E number* * This information can be found on the rating plate, which can be seen when the grease filters are removed. Technical Specifications Model: DE 3160 - CHDE 3160 Dimensions: (in cm): Height 40 Width 59,9 Depht 27 Maximum absorbed power: 200 W Motor absorption: 120 W Lighting: 2 x40 W Length of the cable: 150 cm Mounting accessories included 1 Flange O 100 mm 1 Flange O 120 mm 2 Hooks 2 rails 1 Deflector 2 Washers 4 wood-screws 5 x 45 mm 4 Wall plugs O 8 mm 1 Metal-screw 2,9 x 9,5 6 wood-screws 4,5x16 10 wood-screws 4,5x13 1 Spacer Electrical connection Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board. When installing, an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided. The manufacturer declines all responsibility for malfunctions resulting from failure to comply with the above instructions. Electrical connection 220-230 V – by means of fixed power cable with plug. (Fixed connection of the appliance must only be carried out by an authorised electrician.). Installing the hood between cupboards with hanging rails • Remove the grid. Fig. 6. • Take off the visor G. Fig. 13. • Mount the two hanging rails directly underneath the edge of the cupboard using three screws 4,5 x 16 mm in each rail. Distance from first hole to front edge of the cupboards sides must be 153 mm. Fig. 8. 153 Fig. 8 • Push the extractor hood over the two hanging rails, then fix the hood from its inside to the cupboards sides with two screws (4,5 x 13) through the lower holes of the hood. Fig. 9. Fig. 9 • Refit the visor. Fig. 13. • Refit the grid. • Fit the spacer M on the hood with two screws O and washers, ensure that there is not a gap between the back of the hood and the wall by adjusting the spacer M tightly to the wall, using the screws O. Fig. 11. Installing the hood to the wall It is possible to fix the hood in position, if necessary, by only attaching it to the rear wall. Proceed as follows: • Drill four O 8mm holes on the wall as indicated. Fig. 10. 600 529 35 509,5 34,8 Fig. 10 • Insert the four wall plugs supplied into these holes. • Screw the two mountings hooks P into the top two wall plugs. Fig. 11. 0-90 0-54 54-100 Fig. 11 • Fix the base spacer M to the wall with the two screws R 5x45 provided using either the long or the short arm, depending on the depht of the side cupboards. Do not tighten the screws fully. Fig. 11. • Fix the hood to the wall by means of the two hooks P previously mounted, but first move the upper brackets S so that the front panel of the hood, once mounted, will be in line with the front edge of the cupboard doors. The two upper brackets S, located at the top rear edge of the hood may be slid backwards and forwards by loosening its fixing screws T adjacent to them on the upper hood surface. Fig. 11. • Check that the hood is at the right height. Minor height adjustments may be made with the screws U embodied in the brackets. Fig. 11. • Tighten the two wall fixing screws R, through the two access holes N provided on the inside of the hood then fix the lower sliding frame to the hood with two screws O and washers. Fig. 11. Fixing a furniture door to the visor Before fixing the furniture door to the visor, please ensure the distance distance between the plate and the upper edge of the cabinet door is correct (depends on the thickness of the material and whether or not there is an upper shelf). Fig. 6. a b 0= 17 16 = 33 19 = 36 b a Fig. 12 • Remove the grid. Fig. 6. • Take off the visor G by turning the rear locking knobs H. Fig. 13. Fig. 13 • Draw a line with a pencil on the middle of the internal side of the furnituture door. Fig. 14. = = Fig. 14 • Fit the visor upon the internal side of the furniture door so that the line previously marked on it, is visible through the two triangles holes located on the mid upper and lower side of the visor, having care to respect the distance from the visor to the highe...
Questo manuale è adatto anche per i modelli :Piani di cottura - DE 3160 (436.38 kb)
Piani di cottura - DE 3160 (436.38 kb)
Piani di cottura - DE 3160 (436.38 kb)