valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
SpeedZone Computer (1) 2. Mounting bracket (1) 3. Magnet with screw (1) 4. Cable tie wraps (4) 5. Mounting bracket sizing straps (3) 1 2 3 5 4 FIGURE 1: FIGURE 2: SENSOR MAGNET PLACEMENT ATTACHMENT MOUNTING THE SPEEDZONE COMP The SpeedZone Comp sensor can mount on the right or the left side of the fork blade. Use the cable tie-wraps provided to position the sensor. Do not tighten until the final placement of the sensor magnet is correct. ( See figure 1) FIGURE 3: MOUNTING BRACKET Attach the magnet to a spoke across from the sensor with the magnet screw. The clearance between the magnet and the sensor should be approximately 1/32"-1/16" (1-2mm). Tighten the magnet and transmitter. Do not overtighten the magnet screw. ( See figure 2.) Attach the mount to the handlebar using the bracket screw provided. Tighten so that the bracket cannot rotate on the handlebar. There are several sizing straps odometer "FUNCTION" diameter bars. See figure 3) computer can ‘tap’ the "MODE" Slide the computer onto the modes by pressing Km/h, m/h indicator mounting until it ‘located on the right-ing. You may now alternate between an audible click. To remove the comhousing. Once a specific miles and kilometers puter, push it backward until been entered, its values "MODE" button. When from the mount. To test for proper or adjusted by pressing either choice is flashing, select it installation of the magnet, sensor "FUNCTION" button located on the "FUNCTION" button. You will now computer, activate the computer by left hand side of the housing or by enter the "Programmable Odometer" picking up the front of the bicycle and using a combination of the "MODE" mode. If the odometer setting is correct spinning the wheel. The "wheel option" and "FUNCTION" buttons. push the "FUNCTION" button five indicator will flash. If it does not flash, times to exit odometer mode. check the sensor and magnet align1. Miles or Kilometers selection (Otherwise, see "Setting the ment. Realign as necessary until the Your SpeedZone Comp will record Programmable Odometer" below). "wheel option" indicator flashes while speed and distance in either miles spinning the wheel. (M/h) or kilometers (Km/h). To enter 2. Setting the Programmable your selection of miles or kilometers, Odometer PROGRAMMING push the "MODE" button until ODO To access the programmable odometer Programming the functions of your (odometer) appears in the lower left mode, first advance the "MODE" but- SpeedZone Comp requires it to be side of the display (This is called the ton until (ODO) appears on the left- placed in various "modes" (i.e. odometer mode). Hold down the hand side of the screen. Then hold 4 FIGURE 4: PROGRAMMABLE ODOMETER SCREEN down the "FUNCTION" button and ‘tap’ the "MODE" button once. (See figure 4) The Km/h indicator will flash. If the Km/h setting is correct press the "FUNCTION" button once and a five-digit number will appear. You are now in the programmable odometer mode. This mode is useful if you have replaced the battery and would like to retain the mileage you have already ridden. enter a odometer, press the until the flashing (Note: The "MODE" button scroll to the correct digit.) Press the "FUNCTION" button to digit to the right. Repeat this until all five digits are entered existing mileage. 3. Wheel Circumference Selection To set the circumference for the type of tires you are using, you can use Specialized’s exclusive "Easy Calibration Mode" or measure your actual tire circumference by the rollout method. Two different tire diameters may be entered into the computer’s "Second Wheel Option." Easy Calibration Your SpeedZone preprogrammed 14 Specialized tire 26 X 1.0 26 X 2.2 26 X 1.25 650c X 20 26 X 1.5 700c X 20 26 X 1.95 700c X 23 26 X 1.9 700c X 26 26 X 2.0 700c X 32 26 X 2.1 700c X 38 When using Easy Calibration Mode, the SpeedZone will display the tire size on its LCD display screen. (See figure 5) The Easy Calibration Mode is accessed by entering the odometer (ODO) mode and holding down the "FUNCTION" button for three seconds. The display will now show the currently FIGURE 5: EASY CALIBRATION SCREEN selected tire size for wheel option #1. To scroll through the preprogrammed tire sizes, tap both the "MODE" and "FUNCTION" buttons simultaneously. When you reach the desired tire size press the "FUNCTION" button once to select it and enter Easy Calibration Mode for wheel option #2. Follow the same procedure to program the wheel #2 tire size button to exit Roll Out Method The roll out method will most accurate computer and can take into account such as inflation pressure, rim and rider weight. 1. Extend a tape measure out to 3000mm (120 inches) and lock it in place. 2. With your tire inflated to its proper pressure, place the valve at the 6:00 position (at the bottom) directly over the start of the measuring tape. 3. Roll the wheel one complete revolution until the valve stem is again at the 6:00 position. Read the tape directly under the valve and note the distance in m...