valutazioni - 7, GPA: 4.4
(
)
)
|
Facilità d'uso
The more familiar you get with this model, the more enjoyable your trips are going to be. Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make you fully benefit from all the technical features of your VDO CYTEC bicycle computer. We wish you enjoyable trips and rides on your bike with VDO CYTEC CYCLE PARTS GMBH 1.1 Mounting the handlebar holder The handlebar holder fits handlebars of any diameter. Before mounting the system, decide if you will be using your left or right hand to operate the computer and then mount the handlebar holder on the respective side. Position the handlebar holder, insert the strap and adjust is by tightening the screw. 1 1.2 Mounting the speed transmitter / sender The sensor should be mounted on the same side of the fork as the holder is on the handlebar. Make sure to position the respective rubber shim between fork and sender, position the curved back of the sender next to the spokes and make sure the sender is aimed at the receiver (computer head). Important: Do not tighten the cable ties yet. Accurately position the sensor and the spoke magnet first, then tighten the cable ties. _ In case this distance is not achievable in the current positioning, slide the sensor and the magnet on the fork or spoke accordingly. Watch out: Please remove the computerhead from the handlebar holder when you intend not to use your bike for a longer period of time, (battery power) 1.4 Installing battery into computer head To save battery power, your VDO CYTEC C05+ comes with the battery not yet fitted. Prior to initial use you have to install the battery first. Insert battery with positive (+) end on top. Watch out: Once the battery is properly fitted, the computer immediately changes into set-up mode (see also chapter 5). If you find the computer is not functioning properly after a battery change, push the AC-button (Auto Clear) on the rear side of the computer to reset. Z 3V CR 2032 “ 1.5 Function Indicator Your VDO CYTEC C05+ features a function indicator ((1)). When you are done mounting the computer, ((1)) flashes at the first rotation of the wheel. When the wheel-size is properly entered, actual speed is displayed as well.(see chapter 5). In case the function-indicator ((1)) is not flashing, please double-check: Is the computer properly fitted onto the handlebar holder? Is the spoke magnet accurately positioned opposite the speed transmitter (max 5 mm distance)? 2. Twist-Click mounting of computer onto holder The Twist-Click mounting has been exclusively developed for the new line of VDO CYTEC computers. The computerhead is put onto the handlebar and by a right turn of the computerhead (TWIST) fixed to the holder (CLICK). It is just as easy to remove the computerhead from the handlebar holder. Slightly push the computerhead down, twist it to the left, remove computerhead from handlebar holder. “ 3. Information features of your VDO CYTEC C05+ Your VDO CYTEC C05+ provides you with following information: KMH-MPH current speed indicated in either KMH or MPH, featuring automatic conversion into MPH DST trip counter, counts your trip distance up to 999,99 km or miles. ATM trip timer, keeps track of the actual riding time featuring automatic start/stop function, up to 9:59:59 (hrs:min:sec) CLK clock with 24 h display mode. ODO odometer, counting distance ridden up to 99,999 KM or M. —— ■——__ GEEeEZniHUHVE Button / Key Covering Your VDO CYTEC C05+ has 1 operating button / key Function fra DST ! CLK ATM CLK [ 8& ODO This button / key has several functions. All functions of the button / key are outlined in the chart below. Your display indicates following information Button / Key to Length of pushing What is going on? be pushed the button / key DST-ODO-CLK-ATM push MODE key brief (0.1 sec) next information from DST or ODO or ATM is indicated. ODO push MODE key long (5 sec) enter set-up mode for wheelsize and odometer CLK push MODE key long (5 sec) enter set-up mode for clock DST push MODE key long (5 sec) DST and ATM are simultaneously reset to ZERO Watch out: To avoid resetting DST and ATM by mistake, thoroughly check the information in display before you push the MODE key for 5 sec. 5. Set-up mode Your VDO CYTEC C05+ features the following set-up procedures wheelsize = WS set-up starts out of ODO in display clock = CLK set-up starts out of CLK in display odometer = ODO set-up starts out of ODO in display Watch out: Once the battery is properly fitted, your VDO CYTEC C05+ immediately changes into set-up mode (see also chapter 5.3). “ 5.1 Programming (setting up) your wheelsize In order for the VDO CYTEC C05+ to indicate your actual speed and your trip distance, the correct wheelsize has to be entered. Wheelsize is the outer circumference of the wheel including the tire. following default is entered wheelsize = WS = 2124 mm Watch out: Above default is automat...