valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
NOTE: Before installing carrier, clean all surfaces of vehicle which may come in contact with the carrier or its straps. Make sure foot pads are free of any debris that could scratch vehicle’s finish. Figure 2 • To adjust rear legs, loosen knobs, remove from end of cylinder and reposition (A). • To adjust arms, loosen knobs, slide to center of aluminum cylinder and rotate (B).NOTE: It is not necessary to move bumper legs, as the bones rack is pre-assembled to fit a majority of vehicles and bicycles. However, it offers the flexibility of a wider arm or base spread if necessary. To do so, remove rear legs, bumper legs, and arms and reposition symmetrically as desired. For questions, see a local Saris dealer or call 1-800-783-7257 (C). 1 ADJUST CARRIER TO VEHICLE: As shown in figure 3c, it is important that the tip of the arms (3rd position) are at the highest point , as shown in Figure 3c. •Following the illustration that most resembles the rear of your vehicle, adjust arm and rear leg to position carrier. •Retighten knobs. Do not overtighten knobs. NOTE: To keep legs/feet firmly against glass of square back vehicles, lean carrier slightly farther away from vehicle. REAR LEG REAR LEG ARMS (A) (B) (A) (C) (C) BUMPER LEGS • Attach S-hook straps to top hinge line of vehicle as shown in Fig's. 4a & 5. Always place strap between car surface and hook. NEVER bring strap over the top of hook (Fig. 4b). S-hook special application: If top hinge line has a rubber seal or indicated in fit guide, use large bend in S-hook. To do so: remove strap from buckle, thread end of strap into either slot in the hook and pull through (Fig. 4c). Rethread strap as shown in Fig. 4d. NOTE: S-hook attachment must be to a supported hinge line - NEVER hook to glass, unsupported plastic, or roof rack. • Attach lower hook straps to bottom edge of trunk at position C2; and side hook straps to the side at position C1 or above bend in trunk at position C3 (Fig. 5). NOTE: For square back vehicles such as mini-vans, make sure the side straps are inline with aluminum cylinder. ATTACH STRAPS: Figure 5 LOWER STRAP HOOK SIDE STRAP HOOK 2 Figure 4a Figure 4b Figure 4d Figure 4c Figure 6 Lower strap hook special application: ONLY IF SPECIFIED IN CURRENT FIT CHART Some vehicles require placing the lower strap hook completely inside the trunk. To do so, loosen lower strap, place hook inside trunk, close trunk, pull strap until hook braces against trunk wall, and tighten as usual (Fig. 6). •Tighten all straps evenly, removing any slack. When straps are taut, shake carrier to check for any movement. Retighten if necessary. 1 2 3 Locking Knobs R R 5253 Verona Road Madison, WI 53711 1-800-783-7257 Made in U.S.A. 10690 Rev. G 02/01 U.S. Patent #5,495,970 3 LOAD AND SECURE BIKES: •Check clearance. It is the responsibility of the user to ensure the necessary clearance (dependent on vehicle, load, driving territory, etc.) is given from load to ground. Generally, 12-15” is adequate (Fig. 10). If necessary, rotate arms up until at least 12-15” of clearance is achieved. • Place bikes on carrier arms in bike supports, alternating direction of handlebars. Pull hold-down strap snug against bike tube. Rest seat tube against stabilizer and pull strap around tube as shown in Fig. 7. • If pedal touches vehicle, rotate arms up. • To release hold-down straps, follow Fig. 8. • Women’s frames can be mounted as shown in Fig. 9. Figure 7a Figure 8 CAUTION: Pulling up on hold-down strap could cause failure Figure 7 Figure 9 Figure 10 CAUTIONS: 1) All requirements for compatability/fit as stated in the current Saris vehicle/carrier compatability guide must be followed. (Available at any Saris dealer). If your vehicle is not listed or you have any questions, please call our customer service at 800-783-7257. 2) Bones is a bumper-supported bike rack. Bumper legs must rest on bumper. 3) Bones is not intended for use with tandem or recumbent bicycles. 4) Read and follow instructions carefully. Save owner’s manual for future reference or parts information. 5) Replace any mounting strap at the first sign of wear. Replacement parts are available through your local Saris dealer or call 1-800-783-7257. 6) S-hook straps must be parallel with the rear leg to prevent shifting. 7) Make sure bike tires are not directly behind exhaust pipe. 8) Never place more than three bicycles (maximum weight 105 lbs) on carrier. Secure properly and adjust for even load distribution. 9) Do not mount to any type of trailer. 10) No part of carrier, including straps, should ever come in contact with spoiler. 11) Do not open rear deck (trunk) with carrier installed. 12) This carrier is not recommended for off-road use or for use at speed exceeding 65 mph. 13) Remove carrier from vehicle when not in use. 14) When cleaning rack, use only water soluble cleaners. 15) Rear window wipers may not be usable while carrier is attached to vehicle. 16) It’s the end users responsibility to ensure that use...