valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
(See the Sections D-1 & D-2 "Removing the Frame Covers.") 2. Detach the CN-3 connector from the power supply board. (Fig. 1) 3. Cut the cable holders which fix the CDC sensor cable to the frame. 4. Remove the defective CDC sensor set by loosening the screws, and mount and fix the brandnew CDC sensor set. (Fig. 2) 5. Perform the following adjustments. (Figs. 3 and 4) © Align the line on the CDC sensor with the center of the line on the CDC magnet. (Fig. 3) © Adjust the gap between the surface of CDC sensor and the surface of CDC magnet to be approx. 2mm. (Fig. 4) * If the gap is inadequate, bend the metal base to secure the specified gap. 6. Securely connect the CN-3 connector to the power supply board. (Fig. 1) 7. Rotate the crank, and check if the pedal cadence will be displayed on the control unit. 8. Fix the CDC sensor cable to the frame by using cable holders. (Fig. 5) 9. Assemble the frame cover. (See the Sections D-1 & D-2 "Removing the Frame Covers.") Line on CDC Sensor Center of CDC Magnet Fig. 2 Fig. 3 O W c o (O O Q O o Cateye Ergociser Series 1000 Service Manual 29 d a o b > e * el c a CL e ro c ci la pl e o' CO CO Cateye ergociser^ m Applicable Models: EC-1600 EC-3700 Replacing the Panel Keyboard 1. Remove the control unit by loosening four screws. Also remove the cable connector from the control unit. (Fig. 1) 2. The control unit can be separated into upper and lower parts when the eight screws on the bottom of the lower body of the unit are removed (Fig. 2). Be careful to separate them slowly since the upper and lower bodies are connected with a flat cable. 3. Remove the connector on the panel keyboard which is located at the upper body side, loosen the nine screws on the substrate, and remove them from the upper body. (Fig. 3) 4. Since the panel keyboard is fixed to the control unit with silicon, cut the silicon with a sharp cutter (Fig. 4). Peel the panel keyboard off the surface of upper body. (Fig. 5) 5. If the silicon remains at the upper body, remove it thoroughly. 6. Place the brandnew panel keyboard. The cable from the keyboard should be pulled in through the hole on the upper body. Press and adhere the panel keyboard in position. 7. Apply silicon at two depicted areas to prevent intrusion of sweat. (Figs. 4 and 6) 8. Mount the substrate and fix it with nine screws, and insert the connector of the panel keyboard. (Fig. 3) 9. Put the upper and lower body together, and fix them with eight screws. 10. Connect the cable connector to the control unit, and mount the unit to the main unit. Fig. 5 Fig. 6 Cateye Ergociser Series 1000 Service Manual 30 Cateye ergociser' Applicable Models: EC-1200 EC-3600 ES-7 Replacing the Button Panel 1. Insert a thin cutting knife, while paying cautions not to damage the control unit, in between the button panel and the body, and carefully peel off the button panel. (Fig. 1) 2. Clean the adhesive agent, if any, on the control unit before placing a brandnew button panel. * Sufficiently press the button panel thus placed. Control Unit Button Panel Fig. 1 e C a CL C o 3 m e Cateye Ergociser Series 1000 Service Manual 31 Cateye ergociser^ H Applicable Models: EC-1600 EC-3700 Replacing the Printer 1. Open the control unit into upper and lower bodies by referring to the Section ES-6 "Replacing the Panel Keyboard (1) & (2)." 2. unit is fixed to the lower body with two screws. Remove these two screws. (Fig. 1) 3. The printer unit can be removed after detaching cable connectors CN-2 and CN-3 of the printer unit. To remove the connector CN-3, just pull it, while to remove connector CN-2, the use of tweezer will be recommended. (Fig. 2) 4. Connect the connector CN-2 of the brandnew printer unit. Then, connect CN-3. For the connection, press it while moving it to right and left side alternatively. 5. Fix the printer unit with two screws. (Fig. 1) 6. Put the upper and lower bodies together, and fix them with eight screws. 7. Adjust the printing darkness by referring to the Section ES-9 "Adjusting the Printing Darkness." 8. Mount the control unit to the main unit. Fig. 2 Cateye Ergociser Series 1000 Service Manual 32 Cateye ergociser' Applicable Models: EC-1600 EC-3700 Adjusting the Printing Darkness 1. Remove the control unit from the main unit. (Fig. 1) 2. Loosen four screws on the bottom of the control unit, and remove the cable connector from the unit. (Fig. 1) 3. Remove the black metal base on the bottom of the control unit. (Fig. 2) 4. Provisionally connect the 5P connector on the bottom of the control unit to the main unit. 5. Turn on the power. Check if the printer symbol appears on the LCD panel and the printer is in the operating condition. 6. Check if the thermal paper is set in position. 7. Adjustment should be done with the control unit positioned horizontally. Press the ADV button on the control panel twice to perform a test printing. A counte...
Questo manuale è adatto anche per i modelli :Biciclette - EC-3600 (6.49 mb)