valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Pending Copyright©2007 CATEYE Co., Ltd. ENG 6 2 3 6 5 7 LOCK 1 Installing Bracket Attach the bracket to the handlebar. 1. Wrap the bracket strap around the handlebar, and put it in the dial. 2. Securely tighten the strap by turning the dial. CAUTION!: • Make sure to tighten the dial by hand. If you tighten it too hard with a tool, the screw threads may be stripped. • When the angle adjustment on the right and left sides is loose, tighten the screw. 3. Cut off the excess bracket strap extending from the dial. CAUTION!: Round off the cut edge of the bracket strap to prevent injury. Installation range To Top tube Rubber strap Ring Gear & Brake Cables Bracket strap Dial Bracket rubber pad Button Switch Handlebar Screw HOW TO MOUNT Top tube 1Light unit 2Battery unit (lithium-ion batteries) 3Battery rubber pad INTRODUCTION Before using the light, be sure to thoroughly read this instruction manual and accompanying "Lithium-ion Batteries". This product combines high-power LEDs, Cateye Opticube lens technology, and compact 4Battery charger lithium ion battery to produce a super bright, extremely durable high-performance light. 5Bracket H34 6Fixing strap 7Cable straps (x 2) Attaching/removing the Light unit • Attaching/removing the Light unit Slide the light unit into the bracket as shown. To remove unit after use, pull it out while pressing the button on the bracket. CAUTION!: Make sure the light unit is cool to the touch before removing it. • Attaching/removing the switch Attach the switch to the handlebar as shown. CAUTION!: Mount the switch unit where it does not interfere with the handling of the bicycle. Make sure that it is securely mounted. 1. Hold the switch at the mounting position and hook the strap on the switch from under the bar. Installing Battery unit Mount the battery unit onto the bicycle frame as shown. 1. Put the battery unit through the loop of the fixing strap. CAUTION!: Check that the position of the fixing strap is within the installation range of the battery rubber pad of the battery unit. 2. Secure the battery unit by wrapping the fixing strap around the top tube so that the battery rubber pad comes into contact with the frame. CAUTION!: Do not wrap the fixing strap from above the cables. Doing so is dangerous because it may interfere with braking and gear shifting. Connecting and Securing cables Connect the light unit with the battery as shown. 1. Connect the plug of the light unit to the battery unit as shown in the figure. CAUTION!: Slide the ring of the plug forward and turn it to lock the plug. It must remain locked when in use. 2. Fix the cables to your frame and/or stem to keep them secured. CAUTION!: • Pay attention to the arrangement of the cable so that it does not interfere with the handling of the bicycle. Do not secure the cable at an acute angle because the wire inside the cable may break. • Adjust the beam angle according to “How to Adjust the Beam Angle” in this manual. A B C #534-1857 #534-1858 #534-1856 #533-8827 UL: #037-5895 #534-1860 UK: #037-5896 EC: #037-5897 AS: #037-5899 SPARE PARTS C A B LOCK 5 4 2 How to Charge Battery unit Important! • If the battery unit is wet, wipe dry with a dry cloth before charging the batteries. • Be sure to use only the supplied battery charger. This charger can accept 100-240 volts. • If the charging indicator flashes green, there is a short somewhere in the circuit. Unplug the charger and remove the cause. • If the charging indicator turns green a few minutes after charging begins or if the indicator continues a fast green flashing, stop charging, unplug the charger from the outlet, and do steps 1 and 2. If the same result occurs repeatedly, the batteries may be deteriorated. • The standard charging time and run time are guideline values and depend on the operating environment. • If the battery unit repeatedly does not meet the proper run time even though it is fully charged, it might be at the end of its operating life. Replace the old battery unit with a new one. The used battery unit should be disposed of properly according to local regulations. 1. Plug the battery charger to an AC outlet. NOTE: Check that the charging indicator flashes red three times as the power lamp turns red. 2. Connect the plug of the battery charger to the plug of the battery unit. NOTE: • Charge the batteries with the plug locked. • When charging is complete, the indicator light changes from flashing red to green. 3. After charging is complete, make sure to unplug the charger from the AC outlet. How to Adjust Beam Angle Adjust the beam angle to avoid dazzling oncoming traffic by slightly loosening the dial of the bracket. NOTE: • Do not loosen the dial too much, or the bracket strap may come off. Loosen the dial just enough to allow the bracket to move slightly. Securely tighten the dial after adjusting the strap. • It can also be adjusted 10 degrees to the left and right. Remaining Battery The color of the battery indicator built into the switch shows how muc...