valutazioni - , GPA:
(
)
)
Produttore : Vision Fitness
File Size : 1.13 mb
File Nome : 57984876-d0ad-4e15-aac8-1608214fa57b.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Box 280 ♦ Lake Mills. Wl 53551 toll free 800.335.4348 ♦ phone 920.648.4090 ♦ fox 920.648.3373 ©2001 Vision Fitness. All Rights Reserved. 11.06 AG10.40PRD REV1 TOOLS & PARTS INCLUDED 5mm T-Shaped Wrench Console Mast Cover Water Bottle Heart Rate Chest Strap Color-coded Hardware Bagi Pedals/Straps Owners Guide Assembly Guide Warranty Card 5mm L-Shaped Wrench HARDWARE INCLUDED 1 ORANGE BAG I M8x65L Bolt Quantity: 2 M8 x 20L Bolt Quantity: 2 M8 Lock Washer Quantity: 4 PINK BAG M8 x 15L Bolt Quantity: 2 M8 Lock Washer Quantity: 2 miOW 84G M5 x 35L Bolt M5 Lock Washer Quantity: 2 Quantity: 2 M8 x 15L Bolt M8 Lock Washer Quantity: 4 Quantity: 8 M8 x 20L Bolt Quantity: 4 II M6 x 55L Bolt Quantity: 8 M6 Lock Washer Quantity: 8 Assembly Guide R2700HRT COMMERCIAL FITNESS BIKE To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order Before proceeding, find your new Fitness Bike's serial number located on the front axle tube, and enter here Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owners Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw. STEP 6 STEPl il ORANGE BAG I * Install the rear foot with the four lock washers (M8), two inside bolts (M8x65L), and two outside bolts (M8x20L). Tighten with the 5mm T-shaped wrench. _y * Slide the console mast boot onto the console mast. * Unfold the wire harness and heart rate wires located in the console mast frame bracket. Attach the wire tie coming from the bottom of the console mast to the wire harness and heart rate wires. Pull the wire tie with wire harness and heart rate wires up through the top of the console mast while simultaneously sliding the mast into the frame bracket. * Secure the console mast to the frame bracket with six lock washers (M8) and six bolts (M8xl5L). Tighten with the 5mm T-shaped wrench. Place the seventh bolt (M8xl 5L) in the rear of the frame bracket and tighten until snug. * Slide the console mast boot down and snap it into dace on the side cover. V_/ STEF3 i PINK BAG i * Mount the upper handlebars to the console mast using two lock washers (M8) and two bolts (M8xl 5L). Tighten with the 5mm T-shaped wrench. * Remove the four mounting bolts from the back of the console. Connect the wire harness and heart rate wires that run through the console mast into the plugs located in the back of the console. Attach the console to the mast with the four bolts removed earlier. * Remove the battery cover on the backside of the console. Plug in the ^J^-volt battery. Reattach the battery cover^ cszx^nzzZW * Attach the seat frame to the sliding seat bracket using four lock washers (M8) and four socket head bolts (M8x20L) and the 6mm T-shaped wrench. • Connect Wires A on the seat handlebar to Wires B on the sliding seat bracket. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four bolts (M8xl 5L). Tighten with the 5mm ^T-shaped wrench. ^ cnzi®niZZ® * Secure the Lumbar controlled seat back and the seat bottom to the seat frame with eight lock washers (M6) and eight bolts (M6x55L). Tighten with the 4mm L-shaped wrench. * Snap the plastic seat cover into place on the back of the lumbar controlled seat. YELLOW BAG * Attach the left and right pedals to the left and right crank arms. Tighten the pedals using the 15mm pedal wrench. * Secure the accessory tray to the seat handlebar with two bolts (M5x35L) and two lock washers (M5). Tighten with the screwdriver....