valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Please read this manual and instructions fully before assembly and use. Please keep this manual for future reference. If you sell or give this product to someone else, please include this Owner’s Manual, and ask the new owner to read the instructions thoroughly before using. WARNING Your trailer is designed for the safe, passive transportation of one child between 12 months and 6 years of age and weighing no more than 22kg (48lbs). It designed only for attachment to an adult pedal cycle and for use at a leisurely pace. Its design is not consistent with off-road, jumping or competitive cycling. Any such unauthorized use may cause a critical failure of the trailer resulting in possible death or injury to the passenger(s) and/or rider. WARNING Not for use with children under 12 months of age! Children must be able to support their own heads! WARNING To prevent injury, please exercise extreme care when folding and unfolding this product! PRIOR TO ASSEMBLY Your Halfords trailer is 95% factory assembled. You need only install the safety flag, and attach the wheels before it is ready to use. This initial assembly should only take around 10-15 minutes, after which all you need do now is familiarize yourself with the essential safety information within this document and you’re ready to go. Assembly and attachment must only be carried out by an adult. Check that all parts are present. If any parts are missing or damaged, please contact one of our Customer Service Representatives by phone at 01332 274242, or by e-mail at customer.sevice@moorelarge.co.uk WARNING Immediately discard all plastic bags and plastic wrapping materials! WARNING Never allow children to assemble, fold, or disassemble this unit! PARTS LIST 1 Frame with canopy, sling seat with 5-point safety harness, tow bar, tow bar coupler and rear wheel brackets attached. 1 2-in-1 Rain cover 1 Safety flag with pole 2 20” Rear wheels No tools are required to assemble this trailer. However, for those bikes without a quick-release axle on the rear wheel, an adjustable wrench is required to attach the coupler plate. WARNING Before using, be sure the product is correctly assembled! ASSEMBLY INSTRUCTIONS 1A 1B 1A. Remove all of the contents from inside the carton and place them on a clean flat surface. Check all the contents against the parts list on page1. Check the contents also for damage. 1B. Set the wheels to the side and remove the black plastic protective caps from the ends of the axles. Remove the rain canopy and flag pole assembly from inside the trailer. STEP 2 Assemble the canopy frame 2A 2B Q/R safety pin 2C Q/R safety pin 2A. Lift the left side panel with the frame joiner housing upward so that the right side panel is visible. Lift the right side panel to expose the crossbar and slide the crossbar through the sling seat. Locate the end of the crossbar into the joiner housing on the left panel. 2B. Insert the quick release safety pin through the end of the cross bar & joiner housing and snap closed. 2C. Insert the quick release safety pins through the front and rear of each panel at the base and snap closed to secure the sides. WARNING Ensure all 5 quick release safety pins are securely locked before continuing! STEP 3 Adjust the sling seat 3A Area of detail in photo 3B 3B 3A. Front view of the trailer with the crossbar secured in place. 3B. To provide more comfort, the sling seat can be adjusted by pulling on one or both sets of straps that run underneath the bottom of the seat. Loosen the straps to allow the trailer to fold flat. STEP 4 Attach the 2-in-1 canopy 4 4. Lay the canopy over the top of the trailer frame with the large window toward the front. Fold back the top edge of the canopy and attach the two rear snaps. Seal the canopy to the rear flap with the hook & loop tape. STEP 5 Complete the 2-in-1 canopy attachment 5A 5B 5C 5A. Attach the two snaps at the front corners of the canopy, and join the front flaps. 5B. The rain shield may be rolled down by undoing the elastic loops. 5C. Secure the rain shield along the bottom edge of the 2-in-1 canopy. STEP 6Attach the wheels to the quick-release brackets and make sure they are secure 6A 6B 6C 6A. Locate the rear wheel brackets on each side of the trailer and read the warnings carefully. 6B. Push one wheel axle completely through the bracket hole until you hear the axle click into place. 6C. IMPORTANT! Pull firmly on each wheel to ensure the lock mechanisms are securely engaged! STEP 7Extend and secure the tow bar 7A 7B 7C 7D Bracket 7A. Lay the trailer on its side with the tow bar at the top and undo the lock pin from the bracket. 7B. Pivot the tow bar all the way forward until the shaft comes to rest in the front part of the bracket. 7C. Insert the lock pin shaft all the way through the forward holes in the bracket and tow bar. 7D. Hook the loop over the end of the shaft and make sure the pin is secure. STEP 8 Coupler attachment for bikes with rear hub nuts. (Note: If your bicycle rear wheel has a ...