valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
Cover that surface with a protective covering and place all hood parts and hardware on it. 2. Determine and mark the centerline on the ceiling where the range hood will be installed. 3. Using the mounting template, mark the location of the support mounting bracket holes, vent cutout (if used) and power supply cable cutout on the ceiling. Use 1-1/4" (3.2 cm) drill and saber saw or keyhole saw to cut openings for power supply cable and vent. (See “Venting requirements” and “Electrical requirements,” Pages 3-5. 4. If venting to the outside install vent system. (See “Venting requirements”, Page 3.) Use caulking to seal exterior wall or roof openings. 5. Run wiring through ceiling according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough power supply cable from the fused disconnect (or circuit breaker) box the to make the connections in the hood‘s terminal box. Do Not turn on power until installation is completed. Use caulking to seal all openings. Installation screw upper chimney screws screw 6. Remove the four screws on the upper chimney and disassemble chimney pieces from support frame. 7. Align support mounting bracket with holes in ceiling. Attach support system frame to ceiling using anchors recommended for your type of ceiling: • Concrete ceiling — use inserts and screws provided. • Wood ceiling — use 4" (10.2 cm) long wood screws. • Plaster or sheet rock ceiling — attach support mounting bracket to ceiling joists if possible. If . 10. Remove the terminal box cover from the range hood. Remove the power supply cable knockout using a flat-blade screwdriver. Do not remove optional remote blower knockout. Attach conduit connector into power supply cable opening so that conduit connector clamping screws are inside the terminal box. slot 1/4" (6.4 mm) bolt ceiling joists are not available, you must build a supporting structure behind the plaster or sheet rock. Make sure the support is connected firmly to ceiling. four set screws 8. Determine the height of the canopy. The range hood requires at least 24" (61 cm) of clearance between bottom of range hood canopy and cooking surface. The bottom of the canopy will be approximately 9" (22.9 cm) below the bottom of the support system. To change the canopy height, loosen the four set screws on the support frame. Adjust support frame to the desired length and tighten all four set screws firmly in place before attaching canopy. If used, attach the vent damper to the inside bottom of the chimney support frame. Make sure damper opens to outside. Excessive Weight Hazard Use two or more people to move and install island canopy hood. Failure to do so can result in back or other injury. WARNING 11. Loosen four bolts located next to exhaust opening so that there is approximately 1/4" (6.4 mm) space between bolt head and canopy. Lift canopy and insert bolts into slots in support system frame. Tighten bolts to support system frame and canopy. 9. Press on handle in front of filters to release filters from range hood canopy. Remove filters and set aside. Electrical connection WARNING Electrical Shock Hazard Disconnect power before making electrical connections. Connect ground wire to green ground screw in terminal box. Failure to do so can result in death or electrical shock. 12. Make electrical connection: . Disconnect power supply. . Feed enough power supply cable through conduit connector to make electrical connections. . Connect the power supply cable to hood terminal box through the U.L.- or C.S.A.-listed conduit connector. . Connect the white wire of the power supply cable with the white lead in the hood using a twist-on connector; connect the black wire of the power supply cable with the black lead in the hood using a twist-on connector. . Connect the power supply green (green and yellow) ground wire under the green, ground screw. . Tighten conduit connector screws. . Replace the terminal box cover. Install chimney sections 13. Connect vent to damper or hood and seal all connections with duct tape. upper chimney upper chimney lower chimney 14. Position upper chimney section on support system frame and secure with two screws. support system frame screw screws upper chimney Fit lower chimney section over upper chimney section. Note: clip hole arrows must point toward ceiling. Check for proper position. Then secure upper and lower chimney sections to support system frame with four screws. upper chimney trim clip clips chimney holes lower chimney trim cliptrim chimney holes 15. Cut upper chimney trim to correct length. Be careful not to bend strips while cutting. Slide clips into trim. Postion to align with chimney holes. Push trim strips so that clips snap into holes. 16. Place filters in canopy opening so rear edge is over flange. Press filters up into position. Check operation 17. Turn power on. control panel location 18. The island canopy hood controls are located in a grey panel on underside of the canopy.To open the pan...