valutazioni - , GPA:
(
)
)
Produttore : Wolf Appliance Company
File Size : 126.5 kb
File Nome : Pro_Hood_Liner_Install.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Electrical Requirements Wolf pro hood liners require a separate, grounded 120 V AC, 60 Hz power supply. The service should have its own 15 amp circuit breaker. Locate the electrical supply within the shaded area shown in the installation illustration on the previous page. In-line and remote blowers require a Romex® (not provided) from the blower to the ventilation hood. IMPORTANT NOTE: You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. Risk of electrical shock. This hood must be properly grounded. Electrical service for the hood must be installed by a qualified electrician in accordance with all applicable national and local electrical codes. Pro Hood Liner Installation wolfappliance.com/specs Install Ductwork To reduce the risk of fire, use only metal ductwork. 10" (254) round, rigid metal duct is recommended for pro hood liners. A straight, short run is most effective and will ensure proper operation. For best results, duct run should not exceed 50' (15 m). For runs exceeding 50' (15 m), a higher CFM blower may be required to maintain proper air flow and performance. A remote blower installed on a short duct run may increase the potential for noise. Internal and in-line blowers require a roof or wall cap (not provided). Connect ductwork to the cap and work back towards the hood liner. Use sheet metal screws and aluminum tape or high temperature duct tape to seal joints between ductwork sections. All pro hood liners include a backdraft damper in the tran- sition assembly. Local codes may require the use of an additional backdraft and/or make-up air damper. Contact your local HVAC professional for specific requirements. Backdraft and make-up air dampers are available through your authorized Wolf dealer. For local dealer information, visit the find a showroom section of our website, wolfappliance.com. PRO HOOD LINERS DUCTWORK INSTALLATION THROUGH ROOF 12" (305) LINER HEIGHT 12" (305) 4" (102) DECORATIVE HOOD FOR 191/4" 31" (787) TO 36" (914) FOR 221/2" 30" (762) TO 36" (914) 191/4" (489) LINER DEPTH 221/2" (572) LINER DEPTH Pro Hood Liner Installation Wall Preparation Minimum 2" (51) x 4" (102) lumber is required to construct wall framing. Refer to the illustration below for mounting hole locations and a cross-section view of a typical instal- lation. Framing must be able to support the weight of the hood and internal blower, if applicable. DECORATIVE HOOD 23/4" 2" (51) (70) #10 x 2" (51) SCREW 8" 4" (102) (203) Mounting hole locations. Installation cross-section. Hood Liner Preparation IMPORTANT NOTE: Remove all packaging material from hood liner and damper. Failure to remove material will obstruct airflow and significantly decrease performance. 1) To remove filters, press upward then rotate bottom outward. Refer to the illustration below. To aide in removal, remove center filter first. Gloves should be worn when handling filters. 2) The damper is packaged inside the hood liner in a separate box. Remove damper from box and place it on top of the hood liner using the hold-down brackets. 3) Secure hold-down brackets to damper flange with screws provided. Refer to the illustration below. 4) Seal with aluminum tape or high temperature duct tape. 5) Connect damper to duct using sheet metal screws and aluminum tape or high temperature duct tape. Verify screws do not affect the operation of the damper. HOLD-DOWN BRACKET SPRING LOWER DAMPER CHANNEL FILTER SIDE VIEW Filter removal. Mount damper. Pro Hood Liner Installation wolfappliance.com/specs Hood Liner Installation Position the hood liner in the desired location. Insert #10 x 2" (59) screws through the mounting holes on the back plate. Verify the screws engage two wall studs or blocking. If additional support is required, drill supplementary holes through the back plate and secure with screws. Electrical Connection Before making electrical connections, make sure the electrical power is turned off at the service panel. IMPORTANT NOTE: Refer to specific installation instruc- tions provided with each blower assembly for additional mounting and wiring instructions. 1) Remove the electrical box cover from inside the hood liner. Insert Romex® from service panel (and Romex® from in-line or remote blower, if applicable) through the back of the hood liner and into the electrical box. Secure with an appropriate electrical connector. Refer to the illustration below. 2) Use wire connectors provided to connect black to black, white to white and green to green/bare wire. For in-line and remote blowers, attach the cord assembly to Romex® from the blower. 3) Place all wiring connections inside the electrical box and reinstall electrical box cover. Verify all wires are secure and not pinched between cover. 4) Insert cord assembly plug into hood liner receptacle. Refer to the illustration below. Turn on power and check operation. ELECTRICAL BOX (INSIDE HOOD) RECEPTACLE (INSIDE HOOD) Location...
Questo manuale è adatto anche per i modelli :Fans - L522212 (126.5 kb)