valutazioni - 4, GPA: 3.8 ( )

Produttore : Sears File Size : 454.26 kb File Nome : Lingua di insegnamento:

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OFA RANGETOP GREASE FIRE, OBSERVETHE FOLLOWING*: 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFULTO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. 2. NEVER PICK UP A FLAMING PAN -You may be burned. 3. DO NOT USE WATER, including wet dishcloths or towels -a violent steam explosion will result. 4. Use an extinguisher ONLY if: A. You know you have a Class ARC extinguisher, and you already know how to operate it. B. The fire is small and contained in the area where it started. C. The fire department is being called. D. You can fight the fire with your back to an exit. • Based on _Kitchen Fir_safetyTips _ published by NFPA. 2. To reduce the risk of Rre or electrical shock,this range hood should not be used with an additional speed control device. 3. To reduce the risk of shock, disconnect power before servicing. 4. To reduce the risk of fire and to properly exhaust air, be sure to duct air outside. PLAN THE INSTALLATION Recommended mounting height is 18 _to 24 _from the bottom of the range hood to the top of the cooking surface. The hood should be mounted to the bottom of a standard wall cabinet. If the hood must be mounted directly to a wall, secure the hood to wall studs. All wiring must comply with local codes and the unit must be properly grounded.The hood is connected to a 110-120vAC lighting circuit (15 amp) in the circuit breaker or fuse box. This range hood is "Convertible'-it may be installed as a ducted or as a non-ducted unit. IFTHE RANGE HOOD ISTO BE NON-DUCTF, D: • Purchase nonMucted (duct-free) charcoal filter Model BPQTE IFTHE RANGE HOOD ISTO BE DUCTED: • Ductwork can be installed vertically or horizontally. • Duct runs should Be as short as possible. • Avoid the use of elbows. • Use duct tape at all joints. • Do not use duct smaller than the discharge on the hood. • For 7" round ductwork installation, use 7 _round damper, Model BP87 (purchased separately). HORIZONTAL DISCHARGE THROUGH WALL CUTOUT DIMENSIONS / WALL KITCHEN CABINET SUPPUED DUCT DD TRANSmON WALL CAP 7." RANGEHOOD / 5." __ w_& In[G_ I VERTICAL DISCHARGE ROOF CAP USING 3V4" x 10" DUCT CUTOUT DIMENSIONS TOP VIEW T EAVE CAP 9" 1 3Y4"X 10" DUCT _'J/I--_"="I_L L,. t-11/2" SUPPLIED DUCT WALL CAP BACK VIEW a!'{] -ELEC. K.O._ ",.I r--3/_" _ T TRANSITION WALL RANGE HOOD VERTICAL DISCHARGE USING 7" ROUND DUCT ROOFCAP CUTOUT DIMENSIONS ADJUSTABLE ELBOW CL _""ROOF TOP VIEW 17 = TDL_ J 9" 7"ROUND DUCT REMOVE BOTH 3." x 10" AND7" HALF ROUND _.J/'l-_,,,:: ,,.. Lll/2 . 7"ROUND DAMPER KNOCKOUTS FOR 7" DUCT _UPPLIED 7" ROUND BACK VIEW X_, o-I IF_ RANGE HOOD DUCT TRANSITION _GtrBLE 3 PREPARATION 1. Use the dimensional drawings (Refer to FIGURES 1 -3) to lay out the range hood's mounting holes, vin'ing access and ductwork by marking the cabinet bottom and drywall where applicable. 2. Make cutouts for wiring and ductwork. 3. If the ho...

Scarica la tua

Per scaricare, digitare 2 cifre :