valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
Additional positioning feature for 5/8”, 1”, & 1-1/4” thick ceiling material: Holes in corners of housing are labeled with various ceiling material thicknesses. Position housing so bottom edge of joist is visible through a matched set of holes. The housing is now in the proper position for that ceiling material thickness. Additional positioning feature for 1/2” thickceiling material: Bend two tabs, on side of housing, 900 outward. Lift housing until tabs contact underside of joist. Mark the keyhole slot on both mounting brackets. Existing Construction 4. Hang housing from nails and pound nails tight. To ensure a noise-free mount, pound another nail through the top hole of each mounting tab. 1. Choose the location for your fan/light in the ceiling. For best possible performance, use the shortest possible duct run and a minimum number of elbows. 2. In attic, position mounting brackets against joist. Trace outline of housing on ceiling material. 3. Set housing aside and cut ceiling opening slightly larger than marked. Page 3 MODEL 758NT V E N T B L K S W I T C H B L U B L K WHT WHT WHT L I G H T ( W H I T E ) GRD VENT ( B L A C K ) S W I T C H B O X U N I T L I G H T S W I T C H L I N E I N B L K R E D WHT GRD SCHEMATIC WIRING DIAGRAM SWITCH BOX LIGHT FAN DUAL CONTROL (purchase separately) WHITE BLACK RED GROUND (bare) WIRING PLATE 120 VAC LINE IN BLUE BLACK RECEPTACLE (FAN) WHITE RECEPTACLE (LIGHT) INSTALL THE HOUSING (continued) ATTACH THE GRILLE PAN AND GLASS SHADE INSTALL THE DUCTWORK FLUSH NOTE: The duct connector has a counter-balanced damper flap. The flap will be CONNECT THE WIRING 1. Snap the damper/duct connector onto housing. Make sure that tabs on the connector lock into slots in housing. Top of damper/duct connector should be flush with top of housing. 2. Connect 4” round duct to damper/duct connector and extend duct to outside through a roof or wall cap. Check damper to make sure that it opens freely. Tape all duct connections to make them secure and air tight. "open" approx. 1" when duct connector is attached to housing. This design permits insulation to be in direct contact with fan/ light housing per UL (Underwriters Laboratories) standards. The slightest backdraft, however, will close the damper flap, preventing air from entering unit or finished space. 4. Place housing in opening so that its bottom edge is flush with finished ceiling. Nail to joist through keyhole on both sides. To ensure a noise-free installation, drive another nail through the top hole of each mounting bracket. Existing Construction 5. Additional mounting holes are provided for installations where access from above is inconvenient or not possible. Nail or screw housing directly to joists or framing. ADDITIONAL MOUNTING HOLES 1. Locate the grille pan over the fan housing and connect the wiring harness plug into white receptacle in the fan housing. 2. Insert rod through center hole of grille pan. Use washer between collar on rod and pan. 3. Thread rod onto grille screw in housing, until pan is tight against ceiling. 4. Install bulbs. Use 60 Watt (maximum), candelabra base bulbs. 5. Place glass shade over mounting rod and align shade onto grille pan. Secure glass shade to grille pan with “claw feet” brackets as shown. 6. Restore electrical power and check operation of the unit. 1. Wire unit following diagram above. Run electrical cable as direct as possible to unit. Do not allow cable to touch sides or top of unit after installation is complete. GRILLE PAN GRILLE SCREW WASHER COLLAR ROD Page 4 MODEL 758NT USE AND CARE USE AND CARE WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE CLEANING OR SERVICING THIS UNIT. BULB REPLACEMENT Remove glass shade. Replace bulbs as required. Replace glass shade. Use 60 Watt (maximum) candelabra base, incandescent bulbs. MOTOR LUBRICATION The motor is permanently lubricated. Do not oil or disassemble motor. CLEANING TO CLEAN GLASS SHADE AND GRILLE PAN: Remove glass shade. Shade can be wiped clean with a mild detergent solution or glass cleaner and dried with a soft cloth. Remove 2 bulbs. Grille pan may be gently vacuumed and wiped clean with a soft cloth. Never use abrasive cloth, steel wool pads or scouring powders on glass shade or grille pan. METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER. TO CLEAN FAN ASSEMBLY: Remove grille pan and unplug fan assembly (black receptacle). Gently vacuum fan, motor and interior of housing. METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER. SERVICE PARTS WARRANTY 99043895A NUTONE ONE YEAR LIMITED WARRANTY NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, NuTone will, at its op...