valutazioni - , GPA: ( )

Istruzioni per l'uso Kobe Range Hoods, Modello CH7742SQ

Produttore : Kobe Range Hoods
File Size : 1.07 mb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Press either Speed Control button once (will start on Low speed) for fan control. See Fig. 4. 3. Press Speed Control button to cycle from QuietMode. through high speed. See Fig. 4. 4. Press Light Control button to turn light on. Turn Off: 1. Press Power Control button once (panel lights will flash for 10 seconds before power will completely shut off). 2. Press Power Control button twice (all power will shut off immediately). 3. If only lights are on, pressing Power Control button once will turn power off immediately. The QuietMode™ feature offers continuous ventilation at a greatly reduced noise level. Light Control Speed Control (Cycles through Low, Medium, High, QuietMode. ) Speed Control (Cycles through Low, QuietMode. , High, Medium) Power Control {Fig. 4} Q 9 - MAINTENANCE OF THE HOOD - ----SAFETY WARNING---- INTERIOR OF HOOD MAY HAVE VERY SHARP EDGES, PLEASE WEAR PROTECTIVE GLOVES IF YOU HAVE TO OPEN THE HOOD FOR CLEANING OR SERVICING. Cleaning To clean the hood surface, use only mild soap or detergent solutions. Dry up surfaces using soft cloth. CAUTION: Never use abrasive cleaners, pads, or cloths. If the hood looks splotchy (stainless steel hood), use an orange base cleaner to clean the surface of the hood (make sure the cleaner does not get on any control switches). Spread a light coating over the surface of the hood and leave on for a few minutes (do not leave on too long or there might be damage to the hood finish). Use a soft towel to wipe off the cleaning solution, gently rubbing any stubborn spots. Use a slightly damp towel to get rid of any cleaning solution. Use a dry soft towel to dry the hood. To bring the glow back into a stainless steel finish, use a stainless steel cleaner. To clean hood fans, turn on high speed and spray a mild degreaser into the fans. Liquid residue will accumulate in the oil containers located at the back of the safety screen. These slide easily in and out for cleaning. The round transparent holders attached to the fan cover can be unscrewed (turn counterclockwise) for cleaning. (To replace, just screw back in turning clockwise until it clicks into place.) To clean the fan safety screen, remove the screw (leave in a safe place), and slide safety screen out. Both oil containers and fan safety screen should be washed with warm soapy water and completely dry before returning in place. (Both are top rack dishwasher safe.) CAUTION: Never put your hand into the area housing the fan while the fan is operating. For the most efficient operation of your range hood, clean the range hood surface, fans and optional filters regularly. CAUTION: Drain oil holders before oil can overflow. 10 Changing the Light Bulb 1) Make sure all control switches are off and range hood is unplugged. CAUTION: Wait until light is cool to the touch before changing. 2) Use a flat head screwdriver to pop out the protective covering. 3) Gently pull out the defective halogen light and discard. Plug in new halogen light (12V 20W max.). 4) Replace protective cover. 5) Plug in range hood. 12V20W Troubleshooting Guide Problem Solution Light does not turn on. .. Check power is plugged in. .. Check light bulb. Fan is not turning. .. Check power is plugged in. .. Check electrical wires if connected correctly. .. Check for loose wires. .. Check switch Keyhole 11 - CIRCUIT DIAGRAM - CH-177 Models 12 - PARTS - 13 - PARTS LIST - 1 Plastic Multi Duct Exhaust Attachment 22 Light Transformer Support Screw 2 Plastic Vent Cover 23 Light Transformer Support 3 Plastic Rear Vent Cover 24 Transformer 4 Plastic Vent Cover Screw 25 Control Support Screw 5 Rear Plastic Vent Cover Frame 26 Control Support 6 Hood Casing 27 Control Panel 7 Motor Chamber 28 Control Board 8 Motor 29 Capacitor 9 Turbine Impeller 30 Processor Board Box 10 Oil Tunnel Ring 31 Processor Board 11 Oil Tunnel 32 Round Head Screw (TS 3” x 15”) 12 Bottom Casing 33 Light Transformer 13 Rear Oil Container 34 Motor Position Screw 14 Impeller Safety Screen 35 Round Head Screw (TS 4” x 12”) 15 Oil Container for Safety Screen 36 Bottom Casing Screw (3/16” x .”) 16 Power Cord 37 Impeller Plastic Cover 17 Flat Head Screw (3/16” x .”) 38 Impeller Safety Screen Screw (3/16” x .”) 18 Power Cord Frame 19 Round Head Screw (3/16” x 3/8”) 20 Round Head Screw (TS 4” x 12”) 21 Halogen Light 14 - SPECIFICATION - STYLE CH-177 MODELS Size 30” 36” 42” 48” Dimension (WxDxH) 30” x 22” x 9” 36” x 22” x 9” 42” x 22” x 9” 48” x 22” x 9” Net Weight (lbs) 48.5 50.6 52.8 55 Features: Stainless Steel #304 . . . . Fan Type Turbine Impeller Turbine Impeller Turbine Impeller Turbine Impeller Control Button 6 6 6 6 Halogen Light (12 Volts) 20W x 2 20W x 2 20W x 3 20W x 3 Duct Free* . . . . Safety Screen 2 2 2 2 Oil Container 4 4 4 4 Accessories: (Additional Purchase) Back panel . . . . 6” Round Charcoal Filter . . . . Multi Duct Exhaust: 6” Round (Top) . . . . 7” Round (Top) . . . . 3.” x 10” (Top) . . . . 3.” x 10” (Rear) . . . . *When used with optional 6” round charcoal filter. CH-177 Mod...