valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Vent unit to outside of building, only. • •••••On avarage 2 to 3 hours are necessary to complete installation (without considering cut to be done on wall and or on cabinet, installation of ducts , conduit and electrical connections to the mains). • •••••The hood is fitted with Screws and Drywall Anchors suitable for most surfaces, consult a Qualified Installer, check if they perfectly fit with your cabinet/wall. • ••••• Do not use flex ducting. • •••••COLD WEATHER installations should have an additional backdraft damper installed to minimize backward cold air flow and a nonmetallic thermal break to minimize conduction of outside temperatures as part of the ductwork. The damper should be on the cold air side of the thermal break. The break should be as close as possible to where the ducting enters the heated portion of the house. • •••••Make up air: Local building codes may require the use of Make-Up Air Systems when using Ducted Ventilation Systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area. • •••••T TTTTTypical installation ypical installationypical installationypical installationypical installationypical installation Min installation height from the range top to the bottom of the hood is 30" if a gas range is used or 24" to 30" if an electric range is used. These hoods ar These hoods arThese hoods arThese hoods arThese hoods arThese hoods are not r e not re not re not re not re not recommended to be used ecommended to be usedecommended to be usedecommended to be usedecommended to be usedecommended to be used over indoor grills. over indoor grills.over indoor grills.over indoor grills.over indoor grills.over indoor grills. The hood may be installed onto a wall and vented to the outdoors, or it can be installed for recirculating operation (recirculating accessories not supplied with the hood). This hood can be installed over any electric and gas cooktop/range. It can not be installed over any pr It can not be installed over any prIt can not be installed over any prIt can not be installed over any prIt can not be installed over any prIt can not be installed over any professional ofessionalofessionalofessionalofessionalofessional cooktop / range. cooktop / range.cooktop / range.cooktop / range.cooktop / range.cooktop / range. Installing pr Installing prInstalling prInstalling prInstalling prInstalling preparation eparationeparationeparationeparationeparation Advance planning Advance planningAdvance planningAdvance planningAdvance planningAdvance planning • Determine the exact location of the vent hood. • Plan the route for venting exhaust to the outdoors. • Use the shortest and straightest duct route possible. Refer to “Ductwork installation guidelines Ductwork installation guidelinesDuctwork installation guidelinesDuctwork installation guidelinesDuctwork installation guidelines Ductwork installation guidelines” paragraph for further informations. • Install a wall cap with damper or roof cap at the exterior opening. Order the wall or roof cap and anytransition needed in advance. • Use 8" round metal ductwork only. W WWWWWall framing for adequate support all framing for adequate supportall framing for adequate supportall framing for adequate supportall framing for adequate supportall framing for adequate support • This vent hood is heavy. ‘Adequate structure and support must be provided in all types of installations. Thehood must be secure to vertical studs in the wall, or to a horizontal support. • The vent hood should be on site before final framing and wall finishing. This will help to accurately locatethe duct work and electrical service. • Installation will be easier if the vent hood is installed before the cook-top and countertop are installed. Removing the packaging Removing the packagingRemoving the packagingRemoving the packagingRemoving the packagingRemoving the packaging Remove carton carefully, Wear gloves to protect against sharp edges. Remove the protective film covering the product before putting into operation. Installing the hood Examples of possible ducting . . . . . . . Ductwork installation guidelines For safety reasons, ducting should vent directly outdoors (not into an attic, underneath the house, into the garage or into any enclosed space). Keep duct runs as short and straight as possible. Duct fittings (elbows and transitions) reduce air flow efficiency. Back to back elbows and „S“ turns give very poor delivery and are not recommended. A short straight length of duct at the inlet of the remote blower gives the best delivery. Transition to duct from the integral blower or remote duct transition as close to the downdraft as is possible. In order of preference, use 1st. 10" round duct 2nd. 8" round duct 3rd. 3-1/4" x 14" duct 4th. 7" round duct 5th. 3-1/4" x l0" duct 6th. 6" round duct The use of flexible metal round duct should only be used when ...
Questo manuale è adatto anche per i modelli :Fans - 316488524 (1.6 mb)
Fans - EI36WC55GS (1.6 mb)