valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
0 A17 0 I A18 ON OFF A21 Test the motor. If the motor does not run, check the plug connection. A22 E1 Go to step on page 17 to attach grille. 023_41953_EngS_2-15-08.indd 7 2/16/08 12:25:32 PM 41953-01 02/15/2008 Slide the mounting rails into brackets. Mark position of screws by using holes as a template. Insert screws, leaving space between the screw head and the joist. Screws are not provided. B11 E F 5/8 1/2 5/8 1/2 B12 1/8” bit B14 B15 B16 F B13 Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. Drill a hole in the center of each outline. Attach the rails onto the screws. New Construction – suspended between joists 023_41953_EngS_2-15-08.indd 8 2/16/08 12:25:33 PM 41953-01 02/15/2008 Tighten screws. Route wires through the strain relief. B17 B18 Connect wires as shown. A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option B19 B21 Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. H B20 G Connect 4” duct and vent to the outside. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. 023_41953_EngS_2-15-08.indd 9 2/16/08 12:25:35 PM 41953-01 02/15/2008 10 B27 E1 Go to step on page 17 to attach grille. B22 I Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. I B23 Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. B25 Turn on the power source. ON OFF B26 B24 J Test the motor. If the motor does not run, check the plug connection. Secure the motor by tightening the 2 screws. 023_41953_EngS_2-15-08.indd 10 2/16/08 12:25:36 PM C12EFExisting Construction – accessible from above EXISTING FAN C11 NO EXISTING FAN 9”9.75” ORRemove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (9”x 9.75”). Cut out an opening for the housing. Use the motor housing as a template to mark position. Slide the mounting rails into brackets. 5/81/25/81/2C13C14 position the correct depth mark at the bottom edge of the Mark position of screws by using holes as a template. joist based on the thickness of your sheetrock. 11 41953-01 02/15/2008 023_41953_EngS_2-15-08.indd 11 2/16/08 12:25:37 PM 41953-01 02/15/2008 12 C17 C18 C19 C20 C15 C16 Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. Attach the rails onto the screws. Tighten screws. Connect 4” duct and vent to the outside. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. Route wires through the strain relief. 023_41953_EngS_2-15-08.indd 12 2/16/08 12:25:38 PM 41953-01 02/15/2008 13 C21 Tighten the strain relief screws. A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground Night Light Night Light Switch 1 (AC In) Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option C22 Connect wires as shown. C24 I H C23 G Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. 023_41953_EngS_2-15-08.indd 13 2/16/08 12:25:39 PM 41953-01 02/15/2008 14 C25 I C26 J C27 ON OFF C28 Secure the motor by tightening the 2 screws. Turn on the power source. C29 E1 Go to step on page 17 to attach grille. Test the motor. If the motor does not run, check the plug connection. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. 023_41953_EngS_2-15-08.indd 14 2/16/08 12:25:41 PM 41953-01 02/15/2008 15 D11 EXISTING FAN F D12 Existing Construction – accessible only from below D13 2 1 D14 Route wires through strain relief. Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (9”x 9.75”). Move the housing into position above the ceiling. Attach existing ducting to duct connector. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. F D15 Install the housing flush with the sheetrock and secure by tightening the pre-loaded screws into the joist. 023_41953_EngS_2-15-08.indd 15 2/16/08 12:25:42 PM 41953-01 02/15/2008 16 I D18 I D19 D20 J Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. Secure the motor by tightening the 2 screws. A 3 Pin 2 Pin Fan Motor Light Light Green Black Black Red Red White Black Black White White Bare Copper Ground Night Li...
Questo manuale è adatto anche per i modelli :Fans - 83003 (8.42 mb)