valutazioni - 3, GPA: 5
(
)
)
|
Facilità d'uso
Following the proper mounting diagram, attach the Bracket to the stud using three (3) 5/16" diameter x 2" long Lag Screws (Not Supplied) or appropriately sized Bolts and Nuts if attaching to "I" beams. Wall Mount Assembly (Figure 2) Ceiling Mount Assembly (Figure 3) Insert Bolt through Yoke, Bracket, Pivot Hole, Flatwasher, and into Locknut. (Figure 2) or (Figure 3) While holding Fan in the desired position, firmly tighten the 7/16" Bolt. Figure 2 (Wall Mount Assembly) Fan Head Nut Wall Stud Figure 3 (Ceiling Mount Assembly) Fan Head Bolt Yoke Bracket Yoke Bracket Flatwasher Pivot Hole Pivot Hole Flatwasher Ceiling Stud Nut Bolt MODEL 4TM61C/9020C MANUAL DE INSTRUCCIONES DE OPERACION Y PARTES MODEL 4TM61C/9020C MANUAL DE INSTRUCCIONES DE OPERACION Y PARTES CAUTION: THE SECONDARY SUPPORT CABLE PROVIDED SHOULD BE USED FOR ADDITIONAL SAFETY. SECONDARY SUPPORT CABLE 1. Loop one end of cable around the Yoke. (Figure 5) 2. Attach a Cable Clamp with the "U" on the tail side of the loop leaving a tail approximately 1 to 2 inches. Tighten clamp nuts to 32 inch- pounds torque forming a tight loop. Make sure no part of the cable interferes with the blade. (Figure 5) 3. Wrap the other end of the cable around a secure building joist, truss, or other support near the Fan. If none of these are available wrap cable around the bracket. (Figure 4) Take up excess slack in the cable. Secondary Support Cable Yoke Tight Loop In Cable 1" - 2" Tail Figure 4 Figure 5 20 21 22 25 8 14 12 1110 13 7 11 10 18 17 16 15 19 23 25 24 24 8 26 26 5 6 2 43 1 9 Rev. E 4/01 2 CAUTION: USE ONLY THE MOUNTING HARDWARE WHICH IS RECOMMENDED FOR USE ON THIS FAN. 4. Attach the remaining Cable Clamp as indicated in step 2. The excess tail should be trimmed to extend 1 to 2 inches past the Clamp. 5. Check the assembly to assure the Blade is free of all obstructions. 6. Plug the power cord into a properly grounded three-prong receptacle. CAUTION: USE OF THE SECONDARY SUPPORT CABLE DOES NOT GUARANTEE PROTECTION AGAINST INJURY OF PERSONS, MOUNTING OF BOTH THE CIRCULATOR AND CABLE COULD FAIL IF SUBJECTED TO ABUSE, NEGLECT OR IMPROPER INSTALLATION. OPERATION 1.Plug in cord and select desired operating speed with pull cord. 2. WARNING: This fan should be used only in a clean, dry environment. Mounting of this product in any way other then specified in the instruction sheet will null and void the manufacturers warranty. MAINTENANCE WARNING: ALWAYS UNPLUG THE CORD BEFORE SERVICING. CLEANING: Use a soft cloth and a mild soap solution such as liquid dish washing detergent. CAUTION: Do not use gasoline, benzine, thinner, harsh cleaners, etc. which will damage the fan. Dry all parts with a soft cloth completely before reconnecting to power supply. STORAGE: When not in use, keep unit in a clean dry place. MOTOR IS PERMANENTLY LUBRICATED. REPLACEMENT PARTS LIST Key Part No. Description Qty. 1 2065510 Name Plate 1 2 2050015 Cordset 1 3 2010636 Rear Motor Cover 1 4 2055001 Pull Cord Switch 1 5 ******* Pull Cord with Pendent 1 6 2090552 Wire Nut 2 7 5096037A Rear Grill 1 8 2091126B Screw #6 x 5/8 Type 25 PTH 3 9 2030021SB Motor 1 10 ******* Grill Knob 2 11 ******* Rubber Spacer 2 12 2011604 Yoke 1 13 5082075BKBlade 1 14 5090044 Set Screw 1/4-28 x 3/8" 1 15 ******* Bolt 7/16" -18 x 5" Black 1 16 ******* Flatwasher 7/16" Black 1 17 2060016 Bracket 1 18 5096038A Front Grill 1 19 2091143 Screw #8 x 3/8 Type F PPH 8 20 2070004A Bullseye 1 21 ******* Safety Chain 1 22 ******* Cable Chain Lock 2 23 ******* Locknut 7/16-18 1 24 2091162 Screw #8 x 1/2 Type F PPH 4 25 5060016 Pivot Plate w/Hex 2 26 5090045 #10-32 x 1/2 HWH SERR F-ZP 3 ******* Supplied in Hardware Bag (5098008) 2084796 El VENTILADOR DE MONTAJE EN PARED DE 20" (50.8 cm) 20" (50.8 cm) MODELO 4TM61C/9020C LEA Y GUARDE ESTAS INSTRUCCIONES LEALAS CUIDADOSAMENTE ANTES DE INTENTAR ARMAR, INSTALAR, OPERAR O DAR MANTENIMIENTO AL PRODUCTO DESCRITO. PROTEJASE A SI MISMO Y A LOS DEMAS OBSERVANDO T...
Questo manuale è adatto anche per i modelli :Fans - 9020C (133.02 kb)