valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
C -Indicates speed 1 (LED). D -Indicates speed 2 and saturation of the grease filter (LED) E -Indicates speed 3 and saturation of the charcoal filter (LED) (flashing LED) F -Indicates Intensive speed (LED). G -Intensive speed on/off. The Intensive speed runs for 5 minutes: If the hood is on when the Intensive speed is activated, the hood reverts to previous speed after 5 minutes. If the hood is off when the Intensive speed is activated, the hood will be turned off after 5 minutes. To interrupt the Intensive speed, press button A or B. H -Light OFF I -Light ON A BCDE FG H I Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds, then turn the hood back on again. Correct ventilation If the cooker hood is to work correctly there must be an under pressure in the kitchen. It is important to keep the kitchen windows closed and have a window in an adjacent room open. Important This is not applicable for recirculation. Great care must be taken if the hood is used at the same time as a burner or fireplace (e.g. gas, diesel, coal or wood heaters, water heaters, etc.), as the hood will expel air which is required by these other appliances. In this situation, ensure that a window is open. The negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood. Control device for grease and charcoal filters This hood is fitted with a device that signals when it is necessary to clean the grease filter or the charcoal filter (in the case of recirculation version with charcoal filter). On delivery, the hood is not supplied with an charcoal filter, so the saturation indicator will be disabled. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Press buttons B and G simultaneously and hold them for 3 seconds. At first only the grease filter LED D will light up, but when the charcoal filter LED E lights up the saturation indicator will be enabled. To disable it: Press buttons B and G again simultaneously and hold them for 3 seconds, until the charcoal filter LED goes out. Grease filter LED (D) LED D will start to flash when it is time to clean the grease filter. Cleaning will be necessary after 40 working hours. Always comply with the maintenance instructions for the grease filter. Charcoal filter LED (E) The charcoal filter LED E will start to flash when the charcoal filter needs to be replaced. This operation is necessary after approximately 160 working hours. Resetting the saturation indicator After cleaning or replacing the filters, press button A for 3 seconds until the grease filter LED D or the charcoal filter LED E stops flashing. Maintenance and care • The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood • Clean the outside of the hood using a damp cloth and a mild detergent. • Never use corrosive, abrasive or flammable cleaning products. • Never insert pointed objects in the motor’s protective grid. • Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. • Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. • It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Metal grease filter • The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Removing the metal grease Fig. 3 filter • First, push the metal grease filter stop backwards, then extract the filter, pulling downwards. Fig. 3. Hand washing • Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. Dishwasher • Place grease filters in the dishwasher. Select the most powerful washing programme and highest temperature, at least 65°C. Repeat the process. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. Charcoal filter • The charcoal filter should only be used if you want to use the hood in the recirculation function. • To do this you will need an original AEG charcoal filter (available from your local Service Force Centre). • Cleaning/replacing the charcoal filter for UK The charcoal filters cannot be cleaned, we recommend that they should be replaced approximately every three months or more often if the hood is used for more than three hours per day. • Cleaning/rep...
Questo manuale è adatto anche per i modelli :Fans - DI 8610 (458.6 kb)