valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
• When the hood is used in its extractor function, the following rules must be followed to obtain optimal operation: — short and straight outlet hose — keep bends in outlet hose to a minimum — never install the hoses with an acute angle, they must always follow a gentle curve only — keep the hose as large as possible (preferably the same diameter as the outlet hole). • Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the extractor hood. Description of the Appliance • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • The hood is supplied as a filter unit (with charcoal filter already supplied and fitted) and can also be used with an extractor function function by removing the charcoal filter. Extractor version • The air is discharged to the outside through a pipe, which must be fitted to connection flange D. Fig. 1. • Remove the grease filters and remove the Charcoal Filter K from its housing by unscrewing the two screws that fix it to the hood. Refit the grease filters. Fig. 2. • In order to obtain the best performance the hose should have a diameter equal to the outlet hole. Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/ 125 mm reduction flange provided. In this case the hood will be slightly more noisy. K Fig. 1 Fig. 2 Filter Version • The air is filtered through an AEG charcoal filter and returned to the kitchen through the top grill of the outlet pipe. • You will need an original AEG charcoal filter for the filtering function. • Fix the deflector E using 2 screws O 3,5x6.5 mm. Fig. 3. • Fix the connection flange G using 2 screws O 3,5x6.5 mm. Fig. 3. E G Fig. 3 Hood Operation • Best results are obtained by using a low speed for normal conditions and high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking then you will get an underpressure in the kitchen. It should be left on after cooking for about 15 minutes or until all odours have disappeared. The hood operation may be controlled via the control switches or with the remote control The control switches are located on lower side of the chimney. 1 - Hood OFF. 2 -Decreases the speed 3 -Hood ON, Increases the speed 4 -5’/15’ (minutes) timer push once for 5’ timer, twice for 15’ timer, 3 times to turn the timer OFF 5 -Filter reset 6 -Light ON/OFF F -Saturated filter indicator light -BUTTON 4: Activates and deactivates the timer. Automatically turns the appliance off at the speed in operation. LED on = timer activated - Duration 5 or 15 minutes as set. -BUTTON 5: Once you have replaced the charcoal filters, press this button for at least 3 seconds until the light turns off -BUTTON 4+5: Remote control code programming. Keep both buttons pressed for at least 3 seconds. A beep will sound to indicate that the programming mode has been accepted. Without releasing the buttons, press any one of the remote control buttons. A beep will sound to indicate that the code has been accepted and stored. -F LED: Indicates that the charcoal filter is saturated. This LED is also ON when the hood is used in the extractor version, press BUTTON 5 until the light turns off. Using the Remote Control Button 1 = ON / 1st Speed / 2nd Speed / 3rd Speed/4th Speed/OFF Button 2 = Timer ON/OFF Button 3 = Light ON/OFF Setting the Remote Control Control Before using the remote control, first programme it with the hood: Push Button 4+5, keep both buttons pressed for at least 3 seconds. A beep will sound to indicate that the programming mode has been accepted. Without releasing the buttons, press any one of the remote control buttons. A beep will sound to indicate that the code has been accepted and stored. Remote Control Maintenance Clean the remote control using non abrasive detergents. Follow the instructions below in order to replace the battery for the remote LampButton 2 Button 3 Battery compartment cover Button 1 control : • Raise the cover on the base of the remote control, in order to access the battery compartment. • Remove the old battery and replace it with a new battery type 23A 12V • Fit the new battery taking care to check the polarity as indicated on the base of the battery compartment. Warning! If the remote control doesn’t work , do the following before calling your local AEG Service Force Centre: • Disconnect the hood from the mains. • Reconnect the hood to the mains. • Repeat the procedure described on paragraph “Setting the remote control” Follow this procedure whenever the remote control doesn’t work for any apparent reason (e.g.: dead battery). Maintenance and care • The hood must always be disconnected from the electricity supply before beginning any maintenance work. • Never insert pointed objects in the motor’s protective grid. • Wash the outside surfaces using a delicate detergent solution. Never use caustic deter...