Log:
valutazioni - 3, GPA: 5 ( )

Istruzioni per l'uso Bionaire, Modello BASF1714

Produttore : Bionaire
File Size : 464.31 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


• To disconnect from the electrical supply, grip the plug and pull from the wall outlet. DO NOT pull on the cord. • Always use on a dry, level surface. • Do not operate without the fan grills properly in place. • This product is intended for household use ONLY and not for commercial or industrial applications. ASSEMBLY INSTRUCTIONS (See Fig 1.) Base/Pole assembly You will need the base cover (O), round weighted insert (P), pole (K,M), pole ring (N) washer (S) and L-shaped locking lever (Q). 1. Slide the bottom end of the pole through the pole ring. 2. Turn the base cover upside down and place the round weighted insert into the base cover. 3. Insert the threaded end of the L-shaped locking lever into the hole of the washer, round weighted insert and through the base cover. 4. Whilst holding the base cover and round weighted insert with one hand, connect the Page 4 pole to the base, sliding the L-shaped locking lever into the bottom of the pole with you other. 5. Turn the L-shaped locking lever clockwise to securely attach the pole to the base. 6. Set the base on the floor, weight side down. Push the pole ring down until it sits directly on the base. Fan head assembly You are now ready to assemble the fan head 1. Unscew rear grill mounting nut (D) before positioning the rear grill (F) over the motor shaft (G) making certain that the notches at the top and bottom of the rear grill, fit over the prongs on the motor housing (H). 2. Secure the rear grill in its place using the rear grill mounting nut (D). Turn this nut clockwise and tighten firmly. 3. Slide the fan blade (B) with the hollowed interior of the blade facing toward the rear grill, firmly onto the motor shaft. The top of the motor shaft should lie even with the centre of the fan blade. 4. Now use the securing screw (C) (already attached to the Fan Blade) to lock the blade into place. Tighten the screw into the side hole of the fan blade, against the motor shaft, until both the blade and screw are secure. 5. Centre the front grill (A) by aligning the Bionaire® logo on the logo plate so that it is horizontal and parallel with the floor. Then, holding the front grill against the rear grill, push the black grill ring (E) into place at the top and bottom of the fan. (Push directly on the black grill ring, not on the grills themselves). Finish securing the grill ring in the same manner until both grills are joined underneath the black ring. Final assembly 1. Slide the inner pole extension (K) up from the outer pole (M). Insert the pole locking knob (L) into the hole on the outer pole, to securely hold this position. 2. Place the fan head assembly into this extension pole, inserting the neck of the fan into the pole opening. Turn the fan head's neck until the head is securely locked into place. 3. Add the tilt adjustment knob (J) to the hole in the fan head's neck. Tighten when the fan head is in your desired position. Converting to a table fan - Model 1314 only: On model 1314 an additional short pole (R) is supplied which allows the fan to be converted into a table fan. To change to this short pole, remove the fan head assembly from its position on top of the inner pole and unscrew the L-shaped locking lever at the base. Remove the long pole, replace with the short pole and reassemble as detailed above. OPERATING INSTRUCTIONS 1. Set the fan base on a dry level surface 2. Make sure the Selector (Speed) Control is in the OFF position. Selector (Speed) Control is located on the top of the fan motor housing. 3. Plug the cord into a suitable 220-240V. AC outlet. 4. The SPEED is adjusted by turning the Selector (Speed) Control to the desired setting:O- III-II-I. 5. The OSCILLATION control is located on the top of the fan motor housing. To start oscillation, push the control knob down. To stop oscillation, pull the control knob up. ADJUSTMENT Tilt adjustment Follow these instructions to tilt the fan head for upward angle air movement. 1. To change the tilting angle of the fan head, simply loosen the tilt adjustment knob (J) 2. Move the fan head to the desired angle, then firmly tighten the knob to lock in place. Height adjustment Follow these instructions to adjust the height of the fan. 1. Turn the pole locking knob (L) anticlockwise to loosen the pole. 2. Adjust the pole to the desired height and firmly tighten the locking knob in a clockwise direction. CLEANING AND MAINTENANCE Follow these instructions to correctly and safely care for your Bionaire® fan. Please remember: • Always unplug the fan before cleaning or assembly. • Do not allow water to drip on or into the fan motor housing. • Be sure to use a soft cloth, moistened with a mild soap solution. • Do not use any of the following as a cleaner: petro...

Questo manuale è adatto anche per i modelli :
Fans - BASF1314 (464.31 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie