valutazioni - 3, GPA: 4 ( )

Produttore : Dacor File Size : 705.9 kb File Nome : Lingua di insegnamento:

17. Carefully put the chimney over the top of the framework, taking care not to scratch the surfaces. Make sure the Dacor logo faces the same side as the control panel. 18. Make sure any wires are tucked in behind the chimney and are not pinched. CHIMNEY HOOD TOP FRAMEWORK BOTTOM FRAMEWORK MOUNTING SLOTS insTallaTion insTruCTions hanGinG the ranGe hooD WARNING • To prevent personal injury, do not rely on the mounting springs to hold the hood assembly in place on the ceiling. Once the hood is hooked in place IMMEDIATELY secure the framework to the mounting bracket as described below. 1. Before raising the hood into position, lift it up and orient it so that the control panel faces the same direction as the front of the cooktop or range. 2. Lift the hood assembly up on both sides and slip the end of the framework over the mounting bracket. Push up until all four mounting springs protrude out of the mounting slots on the top of the framework. 3. Attach the framework to the mounting bracket using four self-tapping screws. MOUNTING SPRINGS inStall the Duct work WARNING • Do not use screws to attach the duct work to the hood exhaust outlet. Use duct tape only. Screws may prevent the damper flaps on the top of the hood from opening. • Install the duct work system. Lift the chimney up and reach inside the framework to access the hood exhaust. Attach the duct to the hood exhaust with duct tape alone. Use sheet metal screws (not provided) and duct tape on all the remaining duct system joints. DUCT WORK THROUGH CEILING, CONNECTS TO EXHAUST OUTLET INSIDE FRAMEWORK insTallaTion insTruCTions final electrical inStallation WARNINGS • To avoid electrical shock or fire hazard, make sure the power supply at the fuse or junction box is turned off before proceeding with final electrical installation. • Improper connection of the hood electrical wiring may create an electric shock or fire hazard and may result in damage to the hoods electrical system. • Do not ground the hood to the neutral (white) power supply wire. Connect the hood ground wire to a separate, properly grounded wire installed by a licensed electrician. Connect the house power supply wires to the wires coming out of the hood junction box, inside the chimney: 1. Connect the white wire from the hood to the neutral (white) power supply wire. 2. Connect the black wire from the hood to the hot (black) power supply wire. 3. Connect the green and yellow wire from the hood to the house ground (green) wire from the junction box. BLACK TO BLACK YELLOW/GREEN TO GREEN WHITE TO WHITE final chimney aSSemBly IMPORTANT: Be careful not to pinch the electrical wires while assembling the chimney. 1. Move the chimney up toward the ceiling. Line up the holes on the side of the chimney, above the vents, with the holes on the side of the mounting bracket. 2. Attachthesidesofthechimneytothebracketusingtwomachinescrews,oneoneachside. 3. Carefully,slidethebottomportionofthechimneydownuntilitrestsonthetopoftherangehood. Reinstalltherangehoodfilter(s)beforeoperation. insTallaTion insTruCTions VerifyinG proper operation 1. Turn on power at the junction or fuse box. 2. If the control panel is not lit, remove the filter(s) and turn on the main power switch located behind the filters on the underside of the hood. Replace the filter(s). 3. Touch the light key. Verify that all the lights come on. 4. Touch the light key again to turn the lights off. 5. Touch the blower “+” key once and release. Verify that one light is showing on the blower speed indicator and that the blower is on at low speed. 6. Touch and release the blower “+” repeatedly, three times. Verify that with each touch of the key the number of lights on the blower speed indicator increases and that the blower speed increases. 7. Touch and hold the blower “-” key until the blower turns off. If the hood fails to operate properly: • Verify that power is supplied to the hood. • Check the electrical connections to ensure that the installation has been completed correctly. • Repeat the above test. • If the appliance still does not work, contact an authorized Dacor service company at (800) 793-0093. Do not attempt to repair the appliance yourself. Dacor is not responsible for service required to correct a faulty installation. inStallation checkliSt WARNING • • To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor range hood cannot be overemphasized. . Is the mounting bracket properly attached to the ceiling according to the instructions on page 7? . Is the hood properly secured to the mounting bracket with the machine screws (see page 10)? . Is the duct work completely installed? Are all joints attached with sheet metal screws and wrapped with duct tape (see pages 6 and 10)? . Is the range hood wired and grounded accord...

Scarica la tua

Per scaricare, digitare 2 cifre :