valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
5 5 Run wiring through ceiling according to the n National Electrical Code and local codes and ordinances. Feed enough power supply cable through the wall to make the connections in the hood’s terminal box. Do Not turn on power until installation is completed. Use caulking to seal all openings. Page 3 screws I 6 6 Remove the four screws on the upper n chimney and disassemble chimney pieces from support frame. Personal Injury Hazard Because of the size and weight of this range hood, the support must be firmly attached to the ceiling. l For plaster or sheet rock ceilings, the support must be attached to joists. If this is not possible, you must build a support structure behind the plaster or sheet rock. l Make sure the support is connected firmly to ceiling. . Firmly tighten all four set screws before attaching canopy. Failure to follow these instructions could lead to personal injury or property damage. Electrical connection Electrical Shock Hazard Electrical ground is required on this l the appliance is permanently grounded. . Disconnect power to the junction box before making the electrical connection. *This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance. Install chimney sections 13 13 Attach damper to exhaust opening on n top of the canopy using two Phillips- head screws. Connect ductwork to damper and seal all connections with duct tape. screw Position upper chimney section on n support system frame. Page 4 7 7 Align support mounting bracket with holes in n ceiling. Attach support system frame to ceiling using anchors recommended for your type of ceiling: l Concrete ceiling -use inserts and screws provided. l Wood ceiling -use 4” long wood screws. l Plaster or sheet rock ceiling -attach support mounting bracket to ceiling joists if possible. If ceiling joists are not available, you must build a supporting structure behind the plaster or sheet rock. Make sure the support is connected firmly to ceiling. four set 8 8 Determine the height of the canopy. The n range hood requires at least 24 inches of clearance between bottom of range hood canopy and cooking surface. The bottom of the canopy will be approximately 9 inches below the bottom of the support system. To change the canopy height, loosen the four set screws on the support frame. Adjust support frame to the desired length and tighten all four set screws firmly in place before attaching canopy. 12n Make electrical connection: q Disconnect power supply. q Feed enough power supply cable through conduit connector to make electrical connections. q Connect the power supply cable to range hood terminal box through the U.L.-listed conduit connector. section. Check for proper position. Then secure upper and lower chimney sections to support system frame with four screws. 9 9 Press on n handle in front of filters to release filters from range hood canopy. Remove filters and set aside. 10 10 Remove the terminal box cover from the n range hood. Remove the power supply cable knockout using a flat-blade screwdriver. Attach conduit connector into power supply cable opening so that conduit connector clamping screws are inside the terminal box. Personal Injury Hazard Because of the weight and size of the range hood canopy, two or more people are needed to move and safely install the range hood canopy. Failure to lift range hood properly could result in damage to the product or personal injury. located next to exhaust opening so that there is approximately l/4 inch space between bolt head and canopy. Lift canopy and insert bolts into slots in support system frame. Tighten bolts to support system frame and canopy. q Connect the white wire of the power supply cable with the white lead in the range hood, using a twist-on connector; connect the black wire of the power supply cable with the black lead in the range hood, using a twist-on connector. q Connect the power supply green (green and yellow) grounding wire under the green, grounding screw. q Tighten conduit connector screws. q Replace the terminal box cover. chimney 15 15 Cut upper chimney trim to correct length. n Attach trim strips with clips to cover chimney seam. 16 16 Place filters in canopy opening so rear n edge is over flange. Press filters up into position. Check operation n Turn power on. -\ The range hood controls are located in a n grey panel on underside of the canopy. To open the panel, press on the front edge of panel and release. The control panel will drop down. Grease Fire Hazard To reduce the risk of a range top grease fire: . Keep fan, filters and grease-laden surfaces clean. l Always turn hood ON when cooking at high heat. l Only use high heat setting on range when necessary. l Use low to medium setting to heat oil. l Never leave range unattended when cooking. l Always use cookware and utensils appropriate to the type and amount of food being prepared. In the event o...
Questo manuale è adatto anche per i modelli :Fans - 6899552 (760.09 kb)