Log:
valutazioni - 3, GPA: 4.3 ( )

Istruzioni per l'uso Bionaire, Modello BASF17V

Produttore : Bionaire
File Size : 1.26 mb
File Nome : 2ee64d7f-4bac-8d84-6d8a-4edcd90f3ff6.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


WE STRONGLY RECOMMEND USING THE ORIGINAL BOX FROM PURCHASE. FITTING A REPLACEMENT PLUG FOR U.K. AND IRELAND ONLY. If the plug is not suitable for the socket outlets in your home, it can be removed and replaced by a plug of the correct type. Please refer to "Installation of a plug" below. INSTALLATION OF A PLUG APPLICABLE TO U.K. AND IRELAND The wires in this mains lead are coloured in accordance with the following code: Blue -Neutral Brown -Live This appliance is fitted with a 13 amp plug. The fuse should be rated at 3 amps and ASTA approved to BS1362. However if the plug is unsuitable, it should be removed from the supply cord and an appropriate plug fitted as detailed below: As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red. NB. Neither wire should be connected to the terminal in your plug which is marked with the letter E or by the Earth symbol or coloured Green or Green and Yellow. If in doubt consult a qualified electrician. If any other plug is used, a 3 amp fuse must be fitted either in the plug or adaptor or at the distribution board. NOTE: If the terminals in the plug are not marked or if you are unsure or in doubt about the installation of the plug please contact a qualified electrician. If a 13A 3-pin plug is fitted, it must be an ASTA approved plug, conforming to BS1363 standard. Replacement 3A fuses must be BSI or ASTA BS1362 approved. Page 1 GUARANTEE PLEASE KEEP YOUR RECEIPT AS THIS WILL BE REQUIRED FOR ANY CLAIMS UNDER THIS GUARANTEE. • This product is guaranteed for 3 years. • In the unlikely event of breakdown, please take it back to the place of purchase, with your till receipt and a copy of this guarantee. • The rights and benefits under this guarantee are additional to your statutory rights which are not affected by this guarantee. • Holmes Products Europe undertakes within the specific period, to repair or replace free of charge, any part of the appliance found to be defective provided that: • We are promptly informed of the defect. • The appliance has not been altered in any way or subjected to misuse or repair by a person other than a person authorised by Holmes Products Europe. • No rights are given under this guarantee to a person acquiring the appliance second hand or for commercial or communal uses • Any repaired or replaced appliance will be guaranteed on these terms for the remaining portion of the guarantee. THIS PRODUCT IS MANUFACTURED TO COMPLY WITH THE E.E.C. DIRECTIVES 73/23/EEC, 89/336/EEC AND 98/37/EEC. STAND fan BASF17V BASF17VRC INSTRUCTION MANUAL Holmes Products (Europe) Ltd 1 Francis Grove London SW19 4DT England Fax: +44 (0)20 8947 8272 Email: info-europe@theholmesgroup.com Website address: UK - Free phone Customer Service Helpline – 0800 052 3615 9100010004639 BASF17V/VRCIUK04EM1 grill ring snap into position, holding the grill together. The grill ring must fit evenly around the front and rear grills. If it does not, remove the front grill and check the alignment of the ring on the front grill. 11. Secure the guard using the screw (Q), washer (R) and clip (S) by inserting the screw, from the front, through the hole in the bottom of the guard ring. From the back, put the washer and clip, which has a threaded hole, onto the screw, ensuring the clip is the correct way to fit into the recess on the fan ring. Tighten the screw fully but do not overtighten. OPERATING INSTRUCTIONS 1. Set fan on a dry, level surface. 2. Plug cord into any standard 220-240 volt outlet. Please make sure the speed control is in the off position. For BASF17V only 1. The SPEED is adjusted by pressing the Control Pad button (W) to the desired setting: Off (O) - High (III) - Med (II) - Low (I) 2. The OSCILLATION control (T) is located on the top of the fan motor housing. To start oscillation, push the control know down. To stop oscillation, pull the control knob up. For BASF17VRC only REMOTE CONTROL The Remote Control requires 2 AAA batteries for operation.To install the batteries (not included), simply depress the back of the remote, with your thumb in the indentations, and remove the cover. Insert the batteries according to the diagram shown inside. Replace the cover. All function keys are enabled after pressing the On/Speed key, using the Remote Control unit (V) or the Control Pad (W). On/Speed ( ) 1. To turn the fan On press the On/Speed button. The fan will start to operate at the low speed. You may now choose alternative settings. 2. The fan will be turned Off when you press the Off ( ). 3 By pressing the On/Speed button, you can choose 3 different speeds; successive presses of the On/Speed button cycles the fan...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie