valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
^ If the button is pressed again, the lighting will brighten until the button is released. If the button is pressed continuously, the light will cycle between bright and dark. ^ Press the light button again to turn off the lighting. Operation Filter timers Grease filters A timer monitors the hours of fan operation. The indicator for the grease filter will light after 30 hours of operation. The grease filters must then be cleaned. After the grease filters have been cleaned and put in place, the grease filter timer must be reset. ^ To do this, press the grease filter button for about 3 seconds. The indicator will go out. Charcoal filters The timer for the charcoal filter is not preset. Please program this timer, see "Operation/Reprogramming the charcoal filter timer". The charcoal filter indicator will light once the selected time has elapsed. The charcoal filters must then be replaced and the charcoal filter timer must be reset. ^ To do this, press the charcoal filter button for about 3 seconds. The indicator will go out. Checking the filter timers To check the percentage of time already used: ^ Press the On/Off button to turn the fan on. ^ Press the grease or charcoal filter button. The number of flashing _Aindicators show the percentage of programmed hours that have been used. 1 indicator = less than 25 % 2 indicators = less than 50 % 3 indicators = less than 75 % 4 indicators = less than 100 % This information will remain stored in memory in the event of a power failure. Operation Reprogramming the timers The grease filter timer is preset to 30 hours. This time can be lengthened or shortened to 20, 30, 40 or 50 hours. – A time of 20 hours should be programmed in kitchens with frequent pan or deep frying. – A time of 20 hours should also be programmed if the kitchen is only used occasionally. Otherwise grease which has accumulated over a long period of time will harden on the filters making cleaning more difficult. Reprogramming the grease filter timer ^ Press the On/Off button to turn off the fan. ^ Press the Delayed Shut Down and grease filter buttons at the same time. The indicator for the grease filter and one of the _Aindicators will flash. The lit indicator shows the programmed time: 1st indicator from the left = 20 hours 2nd indicator from the left = 30 hours 3rd indicator from the left = 40 hours 4th indicator from the left = 50 hours ^ Use the $Aor &Abutton to select the desired time. ^ Store the selection by pressing the grease filter button. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. Operation Reprogramming the charcoal filter timer The active charcoal filter can only be used in recirculation mode and can not be used to exhaust fumes. The charcoal filter timer is not preset. Before using the hood in recirculation mode, the charcoal filter timer must be programmed. ^ Turn off the fan using the On/Off button. ^ Press the Delayed Shut Down and Charcoal Filter buttons at the same time. The indicator for the charcoal filter and one of the _Aindicators will flash. The lit indicator shows the programmed time: 1st indicator from the left = 20 hours 2nd indicator from the left = 30 hours 3rd indicator from the left = 40 hours 4th indicator from the left = 50 hours ^ Use the $Aor &Abutton to select the desired time. ^ Store the selection by pressing the charcoal filter button. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. Cleaning and Care Before cleaning or servicing the hood, disconnect it from the power supply by either removing the fuse, unplugging it from the outlet or manually "tripping" the circuit breaker. Cleaning the casing ,Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the hood. They will damage the surface. ^ All external surfaces and controls can be cleaned with warm water and liquid dish soap applied with a soft sponge. ^ Wipe dry using a soft cloth. Do not use too much water when cleaning the controls. Water could penetrate into the electronics and cause damage. Avoid: – cleaning agents containing soda, acids or chlorides, – abrasive cleaning agents e.g. powder or cream cleansers, – abrasive sponges, e.g. pot scourers or sponges which have been previously used with abrasive cleaning agents. These will damage the surface. Stainless steel Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can also be used. Apply sparingly with even pressure. Stainless steel colored controls These controls may become discolored or damaged if not cleaned regularly. Do not use a stainless steel cleaner on these controls. Cleaning and Care Grease filters The reusable metal grease filters remove solid particles from the vented kitchen air (grease, dust, etc). The grease filters should be cleaned every 3 - 4 weeks or whenever the grease...
Questo manuale è adatto anche per i modelli :Fans - DA218 (938.4 kb)