valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Do not use the receptacle and CALL your electrician. 19. Check that neither the appliance nor the power cable have been damaged in any way during transportation. 20. CAUTION: to prevent electric shock match wide blade of plug to wide slot, fully insert. 21. Do not cover the appliance while it is functioning in order to avoid overheating with the attendant risk of fire. SAVE THESE INSTRUCTIONS Your product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. ELECTRIC CONNECTION The fan heater must be connected to a properly polarized A/C 110/120 V household outlet in perfect working condition. Keep loose clothing or bedding, furniture and flammable material away from the wall outlet where the heater is plugged in. When you plug in the appliance, the red pilot light will illuminate (Fig. 1). INSTALLATION The fan heater can be easily positioned on any horizontal support surface in an upright position. FAN HEATER CONTROLS: MANAUTO O °F AM / thermostat dial Fig. 1 red pilot light pointer TIMER ON yellow lamp 3 GB 10-05-2001 9:00 Pagina 4 OPERATION AND USE 1) SETTING THE CLOCK For the first time, set the clock to the correct time, proceeding as follows: • Press the button “hour” until the display shows the hours for the correct time and AM orPM, then release the button (fig.1). • Press the button “min” until the display shows the minutes for the correct time, thenrelease the button (fig. 1). When setting the correct time, the numbers will flash on the display. The flashing of the numbers will continue for a few seconds after the adjustment has finished then stop on the correct time and the clock start working. (Keep both pushbuttons pressed for more than 3 seconds to move through the hours and minutes in fast mode). To change the time, press pushbuttons “hour” for at least 5 seconds, then proceed as above to modify both hours and minutes. O AUTO AM °F current time room temperature 2) MANUAL FUNCTIONING To operate the heater without timer press the “ON MODE” button. (Fig. 1). By pressing the “ON MODE” button one or more times, the appliance will select the operating heating power, as follows: Maximum power Medium power Minimum power Fan only (summer ventilation) Off 4 °F MANAM °F MANAM °F MANAM °F MANAM °F MANAM O GB 10-05-2001 9:00 Pagina 5 If Maximum power has been selected, adjust the thermostat dial (Fig. 1) to the desired comfort temperature, from 42° and 95° F (5°C to 35°C). By turning the thermostat dial the display will show the selected temperature. In addition, the smaller characters on the right-hand side of the display will indicate the actual room temperature (see figure). MAN °F room temperature selected temperature This heater has Electronic Climate Control which automatically monitors and selects the ideal power setting to maintain your chosen temperature. If the selected temperature is higher than the actual room temperature, the appliance will start automatically and rapidly heat the room until it reaches the selected temperature. The unit will automatically maintain the temperature at a constant level, by switching between maximum, medium and minimum power. If the room temperature exceeds the selected temperature level, the appliance will switch off. The appliance will switch on automatically again when the room temperature falls below the selected temperature level. If medium power level has been selected using the “ON MODE” button, the appliance will modulate between medium and minimum power to maintain a selected temperature. 3) ANTIFREEZE FUNCTION Press the “ON MODE” button to select the “P max” power level. Set the thermostat dial to the “*” position (Fig. 1). The display will show 42°F (see figure). When set in this way, the appliance will switch on automatically only if the room temperature falls below 42°F (5°C), to prevent it from freezing, at minimum energy consumption. The display will show “LO” (see figure). This function is not guaranteed in the event of black outs, even if lasting just a few seconds. MANAM 5 GB 10-05-2001 9:00 Pagina 6 4) PROGRAMMING THE ELECTRONIC TIMER The timer allows you to set 2 programmes in a 24 hour period to programme the timer. 1. Press the button “ AUTO” (fig. 2), this accesses the 1st programme (programme A). The yellow timer ON lamp will light up. MANAUTO O °F AM / Fig. 2 TIMER ON yellow lamp 2. Set the start time for your programme by pressing the “hour button” to set the hour AM and PM and the “min” button to set the minutes. 3. To select how long you require the heater to be on, push button “ “ and push repeatedly until your chosen operating timespan appears. The time periods you are a...