valutazioni - 3, GPA: 3
(
)
)
|
Facilità d'uso
It enables users of pressure fryers and deep fryers to operate their fryer in a location without an externally-exhausted ventilation hood and wall-mounted fire suppression system. The exhaust hood is designed to accommodate fryers which hold up to a maximum of 85 pounds of oil (470 square inch vat area) and are supplied with 24 kW of power. Interconnection to the hood’s contactor box provides fire suppression interlock switching of the fryer’s power input. The three-stage filtration system removes oil particles, steam and condensation, and most cooking odors from the exhaust air. The ANSUL® Fire Suppression System actuates automatically if the temperature below the hood exceeds 165°F (74°C), or can be manually triggered by the operator. In either case, fryer operation will be disabled. A damper at the blower outlet will close automatically to restrict air flow to the fire. Safety interlocks disable operation of the fryer if (a) the fire suppression system is not charged and cocked; (b) one or more filters are missing or incorrectly installed; and (c) the exhaust blowers are not operating. Indicator lights aid troubleshooting by pinpointing open interlock switches. Hobart exhaust hoods are produced with quality workmanship and material. Proper installation, usage and maintenance of your exhaust hood will result in many years of satisfactory performance. It is suggested that you thoroughly read this entire manual and carefully follow all of the instructions provided. INSTALLATION Before installing, verify that the electrical service agrees with the specifications on the rating plate located on the left side of the hood by the ANSUL® manual pull. If the supply and equipment requirements do not agree, do not proceed with the installation. Contact Hobart Corporation immediately. UNPACKING Immediately after unpacking, check for possible shipping damage. If the exhaust hood is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Carefully unpack exhaust hood and place in a work-accessible area as near to its final installed position as possible. © HOBART CORPORATION, 2000 – 3 – Locate and identify the following components: 1. Hood and Fire Suppression System 2. Floor Stand and Contactor Box* 3. ANSULEX® Fire Suppressant, 1.5 gallon 4. Drip Cup 5. Grease Filter 6. Air Filter 7. Refillable Charcoal Filter * Back Cover, Right Side Cover, Left Side Cover (optional) LOCATION The installation location must allow adequate clearances for servicing and proper operation. Minimum clearance at the right side and the rear of the unit is 0". A minimum clearance of 30" (76 cm) is required on the left side of the exhaust hood to permit operation of the manual actuator of the fire suppression system. INSTALLATION CODES AND STANDARDS The ventless exhaust hood and fire suppression system meets NFPA Standard #96, Vapor Removal from Cooking Equipment, without requiring a separate exhaust hood. The exhaust hood must be installed in accordance with: In the United States of America: 1. State and local codes. 2. National Electrical Code, ANSI/NFPA-70 (latest edition). Copies may be obtained from The National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. In Canada: 1. Local codes. 2. Canadian Electric Code, CSA C22.1 (latest edition). Copies may be obtained from The Canadian Standard Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3. (electric equipment) ASSEMBLY The exhaust hood is shipped in two pieces. Attach the hood to the frame as shown on page 2. The hood mounting screws will be found in the tapped holes in the floor stand. Push the fryer beneath the hood. Lock casters or set leveling feet as required. POSITIONING HOOD FILTERS The three hood filters must be in their proper positions or your appliance will not function. Fig. 1 shows the long, welded pins (3 on the right and 3 on the left) against which the filters rest. Directly behind the pins on the left side are three shorter filter actuator switch pins which push in and out. Each filter must be placed so that it pushes its filter actuator switch pin in or your appliance will not operate. – 4 – Remove the plastic cover from the Charcoal Filter. The Charcoal Filter goes to the rear of the hood. Notice (Fig. 2) that the actuator pin is pushed in and the filter is resting against the last set of welded pins. Welded Pins Charcoal Filter Actuator Pin Grease Filter Actuator Pin Charcoal Filter Air Filter Actuator Pin Charcoal Filter Actuator Pin PL-40086-1 PL-40087-1 Fig. 1 Fig. 2 The Air Filter is installed next (Fig. 3), and the Grease Filter is installed last at the front of the hood (Fig. 4). Air Filter Grease Filter PL-40088-1 PL-40089-1 Fig. 3 Fig. 4 Insertion and removal of the filters is described in the CLEANING section of this manual. The optional back and side covers may be installed at this time. Install first the back cover and then the two side covers. The overhanging lips of the side cove...
Questo manuale è adatto anche per i modelli :Fans - HVH23 (471.05 kb)