|
Facilità d'uso
During the winter months, the incoming cold fresh air is warmed by utilizing the heat recovered from the stale air before it is exhausted to the outdoors. During the summer months, the cool outgoing stale air from the air conditioned dwelling is used to help cool the incoming fresh air. Your HRV features the digital electronic BASE MODULE that uses a microprocessor to control fan speed and unit operation. Both digital (3 wire) and standard (2 wire) remote devices can control the HRV when connected to the BASE MODULE. TOOLS REQUIRED The following is a list of tools you may require for the installation of your Heat Recovery Ventilator: Reciprocating Saw ■ Electric Drill ■ Flat Srewdriver ■ "Robertson" screwdrivers #2, 3 (square) • Philips for straps ■ Hex head for sheet metal and electrical box Pencil Extension Cord Measuring Tape Knife Duct Tape Hammer Pliers Crimpers Snips (hand shears) For Technical Information Call NUTECH Service Dept. (519) - 457-1904 TABLE OF CONTENTS Tools Required..........................................................1 Engineering Data.......................................................2 Operating Your Heat Recovery Ventilator..................3 Figure #1 A. Base Module Display Panel.........................3 B. Connection to the Base Module...................3 Operating the Base Module.......................................4 Operating Your Digital Electronic Timer.....................5 Optional Remote HRV Controls.................................6 HRV Control System..................................................7 Location for Mounting the HRV..................................8 Figure #2 Model 100 Schematic......................................8 The Ductwork System ..............................................8 A. Outside Weatherhoods..............................9 B. Ducting from Weatherhoods.......................9 Figure #3 Weatherhood Installation.................................9 Fresh Air Supply System.........................................10 Figure #4 Techgrille........................................................10 In-Line Duct Heater.................................................10 Stale Air Return System..........................................10 Electrical Connections.............................................11 Air Flow Balancing...................................................11 Other Installation Methods........................................12 Figure #5 Direct Connection of HRV...............................12 Figure #6 Independant HRV System..............................12 Figure #7 Direct Connection to Furnace.........................13 Figure #8 Direct Connection of both Supply and Exhaust Ducts to Cold Air Plenum.................13 Filtration and the HRV..............................................14 Trouble Shooting Your HRV.....................................15 Dimensions...............................................................16 1 ENGINEERING DATA CORE Single patented aluminum heat recovery core for efficient crossflow ventilation. Meets the flame spread and smoke developed classifications of the National Building Code and NFPA 90A (1993 Edition) MOTORS MODEL 100DEF - Two shaded pole motors. MODEL 100FN - Two high efficiency PSC. FILTERS Washable air filters in exhaust and supply air streams. BLOWERS Centrifugal type rated at 85 CFM when installed at .2 IN WG. Each air stream has 1 motor driving 1 centrifugal fan. CONNECTION DUCT SIZES Four (4) - 5" (125 mm) Diameter UNIT DIMENSIONS Length 24.0" (600 mm) Width 10.5“ (262.5 mm) Height 18.5" (462.5 mm) Weight 52 lbs. (23.6 kg) Shipping Weight 56 lbs. (25.4 kg) MOUNTING Four (4) -10/24" (10.5 mm) threaded inserts at corners of case Four (4) - PVC reinforced polyester straps CASE 20 gauge prepainted galvanized steel (G60) for superior corrosion resistance. Insulated with foil faced fibreglass duct liner where required to prevent exterior condensation. Drain connection, 1 -1/2“ (12mm) O.D. OPTIONAL IN-LINE DUCT HEATERS Often used to temper the HRV supplied fresh air back up to room temperature (or higher). Built-in thermostat. Available in 6" and 7" duct sizes in both 1 and 2 kilowatt. CODES and STANDARDS • CSA Approved. • R2000 Approved. • All components are UL listed. • All units conform to ETL standards. • HVI Certified. CONTROLS ■ BASE MODULE digital control unit. ■ RUN/DEFROST light is illumintated green when HRV is energized and shows red when HRV is in DEFROST mode. ■ 4 illuminated speed indicators. ■ 5 speed motor controlled by autotransformer (4 lower speeds plus HIGH). • Override of BASE MODULE setting to HIGH speed operation by low voltage (12 VAC) remote device. • Standby mode for remote activation of HRV. • Lockout mode to disable operation of HRV. DAMPER DEFROST The Models 100DEF and FN have an electronically controlled damper defrost mechanism. If the outside temperature drops to w...
Questo manuale è adatto anche per i modelli :Fans - 100 FN (2.47 mb)