• It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Special accessories Carbon filter KF825 E-Nr. 942 118 627 Technical assistance service You are welcome to telephone our technical assistance service (see list of technical assistance centres) whenever you need information or in the unlikely event of a fault. When calling, please be ready to specify: 1. The

120 mm dia. for two-motor hoods). Failure to observe these principles is inevitably associated with power losses and increased operating noise. During installation of the fume extractor hood, the following minimum distances from the upper edge of the hob to the lower edge of the fume extractor hood must be complied with: Electric cookers 650 mm Gas cookers 650 mm Coal- and oil-fired cookers min. 700 mm For the kitchen furniture installer General Appliance description The fume extract

. / DKE 73 . . / DKE 93 . . Internet: Bosch Info-Team: de Tel. 01 80/5 30 40 50 (E 0,12/Min. DTAG) de Seite 3–13 pt pagina 69 – 79 en page 14 – 24 sv sid 80– 90 fr page 25 – 35 no side 91– 101 nl pagina 36 – 46 fi sivu 102 – 112 it pagina 47 – 57 da side 113 – 123 es pagina 58 – 68 tr Sayfa 124 – 134 Abb. 1 GAS ELEKTRO GAZ ELECTR. KAASU GASS mind. 650 mind. ELETT. EL. 550 Operating Instructions Appliance description Light / fan switches Chimney panelling Filter grille Lighting Operating modes Ex

3. In buildings with excessively high water pressure, a condition known as “water hammer” may exist. This condition is caused by a combination of high water pressure and the abrupt closing of a faucet valve or internal washer/toilet valve. This instant change in flow results in an instant change in the internal pressures in the pipe, which then sends a shock wave through the pipe. This physical shock will shake, rattle or cause a loud bang in the plumbing which is referred to as “water hammer.”

Bild 2. Handreinigung Metallfettfilterkassette ca. 1 Stunde in hei.em Wasser mit fettlosendem Reinigungsmittel einweichen und danach mit hei.em Wasser abbrausen. Evtl. Vorgang wiederholen. Abgetrocknete Kassette wieder einbauen. Geschirrspuler Metallfettfilterkassette in Geschirrspuler stellen. Reinigung bei starkstem Reinigungsprogramm und hochster Temperatur, mind. 65° C. Evtl. Vorgang wiederholen. Abgetrocknete Kassette wieder einbauen. Beim Reinigen der Metallfettfilter im Geschirrspuler kan

Phillips screw-driver in the spring opening and simultaneously press the springs inwards (towards the appliance housing). Fig. 10. Important: Hold the hood firmly! Adjusting the extractor part (E - Fig. 1) - Fig. 11 On wall units with a body depth of 275 mm to 335 mm, the vapour catcher depth can be adjusted as follows: • Remove both grease filters. • Loosen the screws on both end-stop brackets and set the vapour catcher depth (min. 275 mm, max. 335 mm). • Refit the screws. • Refit the grease fi

1.4 Requirements for installation in Massachusetts Attention residents of the Commonwealth of Massachusetts: In the Commonwealth of Massachusetts the following regulation went into effect on 12/30/2005: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet a