030 HD FREQUENCY For setting the field frequency. 0000 59/23 0: The field frequency is set to 59.94/23.98 Hz. 0001 60/24 1: The field frequency is set to 60/24 Hz. The field frequency which is set here takes effect only when there is no input which supports the OUT REF setting. If there is an input which supports the setting, the field frequency is consistent with the field frequency of input. 031 OUT REF For selecting the video output reference. 0000 AUTO 0: The REF signal (HD/SD) which is input to the REF connector is automatically identified and serves as the reference. If no signal is supplied to the REF connector, the HD serial input signal serves as the reference. If neither the REF input signal nor HD serial input signal is supplied, the internal sync signal serves as the reference. 0001 INPUT 1: The HD serial input signal serves as the reference. If this signal is not available, the unit’s internal reference is used. 0002 HD REF 2: The HD REF input signal serves as the reference. If this signal is not available, the unit’s internal reference is used. 0003 SD REF 3: The SD REF input signal serves as the reference. If this signal is not available, the unit’s internal reference is used. When “1394” is selected as the menu item No.600 [VIDEO IN SEL] setting, the output picture in the E-E mode or output picture during recording may be disturbed in the vertical direction even when this item is set. However, there will be no problem with the pictures which are recorded on the tape. “ ” indicates the factory setting. Setup menus Formats for playback Depending on how the menu item No.020 [SYS FORMAT], No.022 [PB FORMAT] and No.023 [FORMAL SEL] settings are combined, the formats of the tapes played back by the unit differ as shown in the table below. 022. PB FORMAT 020. SYS FORMAT 023. FORMAT SEL Playback format MANUAL 1080i HD-LP DVCPRO HD-LP (1080i) HD-SP DVCPRO HD (1080i) 50M DVCPRO50 (422) 25M DVCPRO (411) 50Mp DVCPROP (420p) DV DV DVCAM DVCAM 720p HD-LP DVCPRO HD-LP (720p) HD-SP DVCPRO HD (720p) 50M DVCPRO50 (422) 25M DVCPRO (411) 50Mp DVCPROP (420p) DV DV DVCAM DVCAM AUTO If AUTO is selected as the menu item No.022 [PB FORMAT] setting, the format applying when the format is not yet detected (when the tape inserted) follows the menu item No.023 [FORMAL SEL] setting. However, if DV or DVCAM is selected, operation proceeds as if HD-LP is selected. DVCPRO HD-LP (1080i/720p), DVCPRO HD (1080i/720p), DVCPRO50 (422), DVCPRO (411), DVCPROP (420p), DC or DVCAM format is detected automatically. OWhen the tape is ejected, the format follows the one selected by menu item No.020 [SYS FORMAT] setting. ODuring DVCPROP playback, the format is down-converted to 480i and output. Setup menus OPERATION Item Setting Description of settings No. Superimposed display No. Superimposed display 101 SHTL MAX 0000 0001 0002 X8.4 X16 X32 For setting the maximum speed in the shuttle mode when using the external controller connected to the 9-pin remote connector. 0: 8.4k normal speed 1: 16k normal speed 2: 32k normal speed The maximum speed for the HD SP mode is automatically limited to 25k normal speed. 102 FF.REW MAX 0000 0001 0002 X16 X32 X50 For setting the maximum speed of fast forward or rewind operations. 0: 16k normal speed 1: 32k normal speed 2: 50k normal speed O The maximum speed for the DV and DVCAM modes is automatically limited to 32k normal speed. O The maximum speed for the HD SP mode is automatically limited to 25k normal speed. 104 REF ALARM 0000 0001 OFF ON For setting whether a warning is to be displayed when the REF VIDEO signal is not connected. 0: No warning is displayed. 1: A warning is displayed by the flashing STOP lamp. 106 EJECT EE SEL 0000 0001 0002 EE BLACK GRAY For setting the video and audio output statuses during eject. 0: Both the video and audio signals are always output in the E-E (electric modulation to electric playback) mode regardless of the position of the TAPE/EE switch. 1: The output status differs according to the position of the TAPE/EE switch. EE: The signals are output in the E-E mode. TAPE: BLACK is output for the video, and the audio is muted. 2: The output status differs according to the position of the TAPE/EE switch. EE: The signals are output in the E-E mode. TAPE: GRAY is output for the video, and the audio is muted. The EE pictures will be all black when the AJ-YA120AG (optional accessory) or AJYAD120AG (optional accessory) is not installed. 107 EE MODE SEL 0000 0001 NORMAL THRU For selecting the output signals in the EE mode. 0: Signals delayed by the time taken by internal signal processing are output. 1: Signal processing is not undertaken internally, and the signals are output without delay at their original timing. The superimposed information is not displayed when THRU is used as the setting. 108 PLAY DELAY 0000 : 0015 0 : 15 For setting the play rise time in frame increments. 109 CAP LOCK 0000 0001 0002 2F 4F 8F For selecti...
)
