valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
Write your code numbers below for future reference. TV: ______ CATV: ______ DSS: ______ Place the supplied label on the back of the remote control. Cable converter/decoder brands Code ARCHER 00, 01, 06, 11, 23, 29 CABLEVIEW 00, 05, 11, 24, 29 CABLETENNA 00, 01 CENTURY 00 CITIZEN 00, 05, 11, 24, 29 CURTIS 19, 25, 32 DIAMOND 00, 01, 29 EAGLE 14, 15, 20 GC BRAND 00, 05, 11, 24, 29 GEMINI 05 GENERAL ELECTRIC 01, 18 GENERAL INSTRUMENT 01, 05, 07, 09, 16, 28, 33 HAMLIN 12, 17 HITACHI 13 JASCO 05 JERROLD 01, 05, 07, 09, 16, 28, 33 MACOM 13 MAGNAVOX 14 MATSUSHITA 08, 21, 41 MOVIETIME 00, 11, 20 NEC 20 NOVAVISION 19, 32 NSC 20 OAK/OAK SIGMA 04 PANASONIC 06, 08, 21, 41 PHILIPS 02, 03, 14, 31 PIONEER 06, 23 PULSER 00, 05, 11, 24, 29 QUEST 06, 23 RADIO SHACK 00 RCA 06, 08, 21, 41 REALISTIC 00 RECOTON 00 REGAL 12, 14, 17 REMBRANDT 00, 01, 11 SAMSUNG 05, 06, 11, 20, 22, 23 SCIENTIFIC ATLANTA 19, 25, 32 SL MARX 00, 05, 06, 11, 20, 22, 24, 27 SPRUCER 06, 08, 21, 41 STANDARD COMPONENTS 00, 11 10 SU4H/UF2 (FVH-T619 GB) Tue. Mar. 09/1999 BASIC ANTENNA/CABLE CONNECTIONS RF CHANNEL 43 VHF/UHF FROM ANT. TO TV OUT IN AC IN Antenna 75 ohm antenna cable VCR (Back panel) TV (Back panel) VHF/UHF ANTENNA IN CABLE TV or 1 (supplied) 324 5 AC Wall outlet 1 Connect an antenna (or a cable TV system) to the VCR. 2 Set the RF CHANNEL switch on the back of the VCR to 3 or 4. 3 Connect the VCR to the TV with the 75 ohm coaxial cable (supplied). 4 Plug the power cord (supplied) into the AC power input (AC IN ~) on the VCR back panel. Insert the plug firmly. 5 Insert the plug end of this power cord into a wall outlet. NOTES: oe If you have a cable converter connected to your TV, see “ALTERNATIVE CABLE TV CONNECTIONS”, next page. oe If your antenna has a twin-lead cable or your TV has screw-type antenna terminals, use a matching transformer (not supplied). 300 ohm Twin-lead Cable Matching Transformer (not supplied) Channel Switch Setting Set your TV to either channel 3 or channel 4. Then set the VCR’s RF CHANNEL switch to channel 3 or 4 to match the channel selected on the TV. This is your VCR channel. The TV must be set to this channel whenever the VCR is used for playing a tape or watching a TV program. If in doubt, check with your local cable company. 11 SU4H/UF2 (FVH-T619 GB) Tue. Mar. 09/1999 ALTERNATIVE CABLE TV CONNECTIONS Your VCR can receive all unscrambled cable channels Your local cable TV company will advise you of the without the use of an external converter. If you wish to channels available in your area. view and record scrambled cable channels, you must We recommend that you consult your cable TV company connect a converter/decoder as described below. to make sure that the cable is properly connected. When the TV does not have a built-in cable converter Connect the cable TV converter between the VCR and NOTE: Set the TV channel to the cable converter output the TV so that you can watch a cable TV program while channel (CH02 ~ 07). recording another program. VCR TV Cable CATV (Back panel) converter (Back panel) 75 ohm RF CHANNEL 43 VHF/UHF ANTENNA ININ OUT (supplied) (not supplied) coaxial cable VHF/UHF FROM ANT. TO TV OUT IN AC IN When you have both cable and pay TV (scrambled channels) NOTES: oe With this method the TV and VCR receive the same oe With this connection, the VCR must be set to the cable channel. Recording one program while watching converter/decoder output channel. (See next page.) another is not possible. Cable VCR TV converter/ (Back panel) (Back panel) RF CHANNEL 43 VHF/UHF FROM ANT. TO TV OUT IN AC IN VHF/UHF ANTENNA IN CATV 75 ohm coaxial cable (supplied) Decoder NOTE TO CATV SYSTEM INSTALLER (USA only): This specifies that the cable ground shall be connected to the reminder is provided to call the CATV system installer’s grounding system of the building, as close to the point of attention to Article 820-40 of the NEC that provides cable entry as practicable. guidelines for proper grounding and, in particular, 12 SU4H/UF2 (FVH-T619 GB) Tue. Mar. 09/1999 ALTERNATIVE CABLE TV CONNECTIONS Cable converter/decoder output channel setup 1 Be sure the cable connections are correct. (See page 12.) 2 Turn on the TV, VCR and cable converter/decoder. 3 Set the TV to channel 3 or 4. 4 Press the VCR button on the remote control to select the VCR operation mode. 5 If the VCR indicator is off, press the TV/VCR button on the remote control. The VCR indicator lights. NOTE: If the initial setup has not yet been completed, the “Auto Setup” message will appear. In that case, first follow steps 5 – 7 under “INITIAL SETUP” on page 15. 6 Press the MENU button on the remote control. The main MENU appears. @@@@@@@@@MENU Timer@program VCR@setup Clock@set Language@select Rec.List@super Auto@tuning@memory [CH§‡]†Select [SET]†OK@@@@@@[MENU]†TV 7 Press the CH/TRACK l (or j) button to select the VCR setup option, then press the SET button. The VCR setup menu appears. CATV/TV@@@@@@@…CATV@TV Cable@box@@@@@…No@@@Ch02 MTS@@@@@@@@@…ST@SAP@Mono Au...