valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
PUSH SET V END : PUSH MENU PREPARAR VCR FIJAR RELOJ FIJAR CANAL esí ELEGIR :PULSE SELEC1 FIJAR : PULSE SET TERMINAR: PULSE MENl I....... REGLAGE MAGNETOSCOPE REGLAGE HORLOGE 1 1 REGLAGE CANAL 1 iLANtiUAGE/ IDIOMAMiHJMlM SEL APP. SELECT A/T REGLER APP. SET FIN APP. MENU 4 Push MENU to exit this mode. Example, if you have cable installed, etc. 1 Push MENU to display the menu. Push the SELECT Up/Down and SET to select SET UP CHANNEL from menu, and then push to set your antenna system (TV or CATV). Push the SELECT Up/Down and SET to select AUTO SET. • If you use a cable box, it must be left on for auto channel set. SET I SET C IDIO* SELECT SET END P VCR LOCK isfcUfJiUM! W/LANGUE:ENGLISH PUSH SELECT A/T PUSH SET KEY PUSH MENU KEY ---- SET UP CHANNEL --- : CATV AUTO SET SELECT SET END PUSH SELECT A/T PUSH SET KEY PUSH MENU KEY 4 Push CH ▲ to start Channel Auto Set. • To exit this mode, push MENU twice. To Set or Reset the Clock In case the clock is wrong, or a power failure occurred. 1 Push MENU to display the menu. 2 Push the SELECT Up/Down and SET to select SET CLOCK from menu, and then to set the time and date. 3 Push MENU twice to start the clock and exit this mode. MENU SET UP VCR Hammaa SET UP CHANNEL IDIOMA/LANGUE: ENGL ISH SELECT SET ENO PUSH SELECT A/T PUSH SET KEY PUSH MENU KEY - vl 7' ' SET CLOCK - - 21 2/1996 FRI gnsnszna BY SELECT A/▼ KEY «-PUSH CLEAR : : PUSH SET TO START PUSH MENU KEY To Add or Delete a Channel 1 Select a channel using the NUMBERED keys. 2 Push ADD/DLT to add or delete the channel. CHANNEL 08 OELETED I or AODEO To select a deleted channel, use the NUMBERED keys on the remote control. Deleted channels will flash in the Multi Function Display on the VCR when selected. When Using the 100 key When selecting CATV channels 100 to 125 with the NUMBERED keys, first push the 100 key and then enter the remaining two digits. For example, to select channel 125: Push NUMBERED keys 100, then 2, then 5. This VCR will accurately maintain its calendar up to Dec. 31, 2014, 11:59PM. Normal TV or Cable channels are automatically selected and placed in memory depending on how your VCR is hooked up. By pushing the SET or CLEAR button repeatedly, you can skip forward or backward over correct entries and go directly to a specific item. 11 Getting Started ni Qn Screen Displays (OSD) Function & Channel Display Whenever a function button is pushed (PLAY, FF, etc.) or the channel is changed, a 4 second OSD will appear first in large and then small characters. MENU Menu Screen 1 Push MENU to display the menu. 2 Push the SELECT Up/Down and SET to make your selection. To get the most from each feature, it is recommended that you read the Operation Manual before attempting any operation. SET UP VCR мдма SET UP CHANNEL ID IOMA / LANGUE : ENGL I SH SELECT : PUSH SELECT */▼ SET : PUSH SET KEY END : PUSH MENU KEY VCR Status & Clock Display Push DISPLAY to display and remove the overlay shown below. Warning and Instruction Displays These displays will alert you to a missed operation or provide further instructions. If no active channels are found for CHANNEL MEMORY... NOCH FOUND PLEASE CHECK ANTENNA CABLE CONNECTION THEN PUSH VCR CH UP KEY AGAIN If you attempt to set or review a Timer Recording and the Clock is not set... PLEASE SET CLOCK BEFORE PROGRAMMING If a Timer Program was not completed before exiting the Program mode... PROGRAM IS INCOMPLETE After a Timer Program has been set... TURN VCR OFF FOR TIMER RECORDING Function Status Time Rec Time - Remaining /SAP (OTR mode only / mono see page 15.) REC 12:00AM CH08 0:25 0:00:00 STEREO *r / SLP Receivable Broadcast Types (See page 20.) (Model PV-4658 only) Channel Counter Tape Speed Blank Tape and will be Blue Screen If a blank section of tape is encountered in the Play mode or the channel you select has no broadcast, the TV screen will change to a solid blue field. The screen will remain blue until a recorded signal is again detected or an active channel is selected. If you push REC on the remote control or REC and PLAY on the VCR, and a cassette is inserted with no record tab... If you push PLAY, FF, REW, or REC on the remote control or if you push REC and PLAY, PLAY, FF, REW, or REC on the VCR without a cassette inserted... If you push POWER or STOP during a Timer Recording... (visible in VCR mode only) CHECK CASSETTE RECORD TAB NO CASSETTE PLEASE INSERT A CASSETTE TO CANCEL TIMER REC PUSH POWER THEN STOP KEY Playback a Tape Check list before you begin □ All connections are made. (See pages 6-9.) □ TV and VCR are plugged in. I | TV is turned on and set to the VCR channel (CH 3 or 4). (3D Multi Function Display Э f в CD О О О ш a c ^ .... ^ ^ ÄNG/ © PAUSE- SLOW' 0*0 ’О о tro 4 I AH PROG ML NO ooo- o:p^ С 11 v0, c M (¿0-0-0 V_CAIV TRACKING/ V-LOCK Caution: Please inspect your cassette tape for any loose or peeling labels as it...