valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
Using the remote commander You can use this remote Remote sensor commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the g symbol near the remote sensor, this remote commander will not operate the TV. TV / VIDEO 1 2 3 4 5 6 To operate the VCR Set TV / VIDEO to VIDEO and point at the remote sensor on the VCR a Sony TV TV and point at the remote sensor on the TV continued Getting Getting Started 5 Step 2 : Setting up the remote commander (continued) 1 2 3 4 5 6 7 8 9 0 I/u DISPLAY ETV/VIDEO Programme number buttons ? PROG+/– c+/– WIDE TV control buttons To Press Turn the TV into standby mode I/u Select an input source of the TV either from ETV/VIDEO aerial in or from line in Select the programme position of the TV Programme number buttons, ?, PROG +/– Getting Started To Press Adjust the volume of the TV c+/– Call up on-screen display DISPLAY Switch to/from wide mode of a Sony wide TV. WIDE Notes • With normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. • Do not use a new battery with an old one together. • Do not use different types of batteries together. • Some buttons may not work with certain Sony TVs. Getting Getting Started 7 Step 3 Step 3 Connecting the VCR If your TV has a EURO-AV connector, see page 9. If your TV does not have a EURO-AV (Scart) connector : Signal flow AERIAL IN Aerial cable (supplied) AERIAL IN AERIAL OUT to mains Mains lead 1 Disconnect the aerial cable from your TV AERIAL ANTENNE panel of the VCR. IN and connect it to AERIAL IN on the rear ENTREE OUT SORTIE 2 AERIAL ANTENNE Connect AERIAL OUT of the VCR and IN ENTREE the aerial input of your TV using the supplied aerial cable. OUT SORTIE 3 Connect the mains lead to the mains. Note • When you connect the VCR and your TV only with an aerial cable, you have to set RF MODULATOR in the OPTIONS-2 menu to ON (initial setting) (see page 47). Getting Started If your TV has a EURO-AV (Scart) connector : Signal flow AERIAL IN Aerial cable (supplied) AERIAL IN AERIAL OUT to mains EURO-AV cable (not supplied) EURO-AV (Scart) Mains lead :LINE-1 (TV) Getting Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR. IN ENTREE OUT SORTIE AERIAL ANTENNE Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable. AERIAL ANTENNE IN ENTREE OUT SORTIE continued Getting Started 9 Step 3 : Connecting the VCR (continued) 3 Connect LINE-1 (TV) on the VCR and the EURO-AV (Scart) connector on the TV with the optional EURO-AV cable. This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press ETV/ VIDEO to display the VIDEO indicator in the display window. 4 Connect the mains lead to the mains. Note • If the TV is connected to the LINE-1 (TV) connector, setting the RF MODULATOR in the OPTIONS-2 menu to OFF is recommended. In the OFF position, only the signal from the aerial is output through the AERIAL OUT connector (see page 47). You do not have to tune your TV to the VCR. Skip “Tuning your TV to the VCR” on page 11. Getting Started Step 4 Step 4 Tuning your TV to the VCR If you have connected the VCR to your TV using the EURO-AV cable, skip this step. I/u ON/STANDBY PROGRAM +/– RF CHANNEL ON/STANDBY Press I/u ON/STANDBY to turn on the VCR. Press RF CHANNEL on the VCR lightly. The factory-preset RF channel appears in the display window. RF CHANNEL The VCR signal is output through this channel to the TV. Turn on your TV and select a programme position for the VCR picture. This programme position will now be referred to as the video channel. Press RF CHANNEL. RF CHANNEL The TV system appears in the display window. Getting continued Getting Started 11 Step 4 : Tuning your TV to the VCR (continued) 5 – PROGRAM + Press PROGRAM +/– (repeatedly) to select the appropriate TV system for your area. Select “G” for the B/G TV system, or “K” for the D/K TV system. 6 Tune the TV to the same channel as that shown in the display window so that the picture on the right appears clearly on the TV screen. Refer to your TV manual for tuning instructions. If you select the wrong TV system in step 5, the picture on the right may not appear. Select the appropriate TV system and tune the TV again. If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below. SONY VIDEO CASSETTE RECORDER 7 Press RF CHANNEL. You have now tuned your TV to the VCR. Whenever you want to RF CHANNEL play a tape, set the TV to the video channel. To check to see if the TV tuning is correct Set the TV to the video channel and press PROGRAM +/– on the VCR. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct. To obtain a clear picture from the VCR If the s...