valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
81-IN5329 04/28/06 FDW75C12N, FDP75C12N IP Ready Network Housing IP Ready Network Housing with 12Vdc input, wall mount or pendant mounting, heater & blowers, ready for standard IP PTZ cameras. ASSEMBLING THE UNIT: Remove content from all boxes. Contents should include: Main Housing Assembly Either with wall mount or pendant bracket ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY): Power 12Vdc, Class 2 Only Total Power: 21 watts Housing only Accessories (Heater/Blower): 21 watts Heater: 20 watts Blower: 1 watt ! NOTE: This unit is designed for operation in an upright position. Installing the housing upside down may cause damage to the internal equipment, and will void the warranty. GENERAL INSTRUCTIONS: Tools Required: .100" Flat Head Screwdriver Phillips Head Screwdriver Be sure the bracket is properly and securely mounted to a supporting structure capable of rigidly holding the weight of the entire unit. ! Dome Assembly - Clear or Tinted Do not remove the protective film until the product is assembled and installed. 3 Packet Assemblies CARE AND CLEANING OF DOMES: All FDW75 and FDP75 units include an optically clear polycarbonate dome. The dome is an optical device and should be handled with extreme care. Leave protective film on dome until product is fully assembled and installed. Even though the dome is virtually unbreakable, it can be easily scratched. Clean only with a clean cotton cloth and warm water. DO NOT use a strong solvent or cleanser! - - INSTALLATION OF PTZ CAMERA See model for specific instruction. Listed on the following pages are the specific instructions for each of the individual network cameras. See specific instruction for the model that matches the unit you have. INDEX OF CAMERAS AXIS 213 5 AXIS 214 6 CANON VB-C10R 7 CANON VB-C50iR 8 CANON VC-C4R / VC-C50iR 9 ELMO PTC-200C 10 ELMO PTC-201 11 ELMO PTC-400C 12 ELMO PTC-401 13 JVC VN-C30U 14 PANASONIC BB-HCM381 / KX-HMC280 15 PIXORD 261 / 262 16 SONY SNCRZ30 17 SONY SNCRZ50 18 TOSHIBA IK-WB21A 19 INSTALLING QUICK RELEASE BRACKETS AXIS 213 2539 Mounting Plate: 1. Install the camera to the 2539 mounting plate using (2) 10-32 screws and lockwashers provided. 2. The Axis 213 camera requires 3.5" of spacing for optimal position within the housing. Use (4) 2" spacer(s), plus (4) 1" spacer(s) and (4) ." spacer(s) provided in the (2) hardware packets. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Attach camera using these (2) holes ." 1" Captive Screw 2" (3) screws in housing INSTALLING QUICK RELEASE BRACKETS AXIS 214 2685 Mounting Plate: Attach camera using these (3) holes 2" 1. Install the AXIS 214 camera to the 2685 mounting plate using the (3) 3mm x 12mm bolt and lock washers provided. 2. The AXIS 214 camera requires 2” of spacing for optimal position within the housing. Use the 4 (2”) spacers provided in the packet. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. INSTALLING QUICK RELEASE BRACKETS CANON VB-C10R 2539 Mounting Plate: 1. Install the camera to the 2539 mounting plate using (2) 10-32 screws and lockwashers provided. 2. The Canon VB-C10R camera requires 4" of spacing for optimal position within the housing. Use (4) 2" spacer(s), plus (4) 1" spacer(s) and (4) ." spacer(s) provided in the (2) hardware packets. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Attach camera using these (2) holes ." 1" Captive Screw 2" (3) screws in housing INSTALLING QUICK RELEASE BRACKETS CANON VB-C50iR 2539 Mounting Plate: 1. Install the camera to the 2539 mounting plate using (2) 10-32 screws and lockwashers provided. 2. The Canon VB-C50iR camera requires 3.5" of spacing for optimal position within the housing. Use (4) 2" spacer(s), plus (4) 1" spacer(s) and (4) ." spacer(s) provided in the (2) hardware packets. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Attach camera using these (2) holes ." 1" Captive Screw 2" (3) screws in housing INSTALLING QUICK RELEASE BRACKETS CANON VC-C4R / VC-C50iR 2539 Mounting Plate: 1. Install the camera to the 2539 mounting plate using (2) 10-32 screws and lockwashers provided...
Questo manuale è adatto anche per i modelli :Video - IP ReadyTM Series Video Alarm FDW75C12N (1.85 mb)