valutazioni - 3, GPA: 3
(
)
)
|
Facilità d'uso
PREFACE The Panasonic Ceiling Mount Bracket WV-Q116 is provided for the surface mounting of the Combination Camera WV-CS954 on a suspended (double) ceiling. PRECAUTIONS • Before installing the camera, make sure that the location where the camera is going to be installed is strong enough to support the entire weight of the camera (approximately 2.9 kg {6.38 lbs}). • Mount this bracket in a suspended ceiling having a minimum of 210 mm {8-9/32”} clearance. • The ceiling board thickness to mount this brack- Suspended et can be a maximum of 40 mm {1-37/64”} in ceiling Maximum 40 mm thickness. {1-37/64”} • Be sure to use the Fall Prevention Wire (provided). • Be sure to lock the camera with the lock plate, and make sure that it cannot come off. • Do not use this bracket with any equipment other than the WV-CS954. • Follow all applicable local and national electrical, fire and safety codes when installing the camera with this ceiling mount bracket. INSTLLATION Be sure to read the "Precautions" before installing the camera. Inside the ceiling (provided) Fall Prevention Angle Clip Fall Prevention Wire Camera Mounting Base Suspended ceiling Combination camera *Refer to the camera’s operation manual. Minimum inside ceiling clearance 210 mm {8-9/32”} The model numbers listed in these Instructions have no suffixes attached to them. 1. Use Template A (provided) to make four holes in the suspended ceiling. 1-1. Make four holes (.12 mm {31/64”} . 4) and then cut and remove the area marked “C”. 1-2. Make the hole round (.220 mm {8-43/64”}) as shown in the following illustration. .220 mm {8-43/64”} Template A 4-.12 mm {31/64”} .220 mm {8-43/64”} “C” 2. Drive a standard anchor bolt (#1 in illustration) into the upper concrete ceiling in the center of the hole made in the suspended ceiling as described in step 1. Drive another anchor bolt (#2 in illustration) into position (2) as shown in the following illustration. 3. Attach one standard anchor nut at point “D”, measured by using Template B (provided). Measure length “E” by using Template B. (2) (1) Template B Anchor bolts Suspended ceiling “D” “E” 169 mm{6-21/32”} 4. Attach the Fall Prevention Angle Clip (provided) to anchor bolt (2) according to the following steps. - 2 Pass through hole Fall Prevention Angle Clip (provided) Fall Prevention Wire (provided) Two spacer nuts are needed to use the existing anchor bolt instead. Existing anchor bolt Spacer nuts Spacer nuts Fall Prevention Wire Fall Prevention Angle Clip 5. Attach the end of the Fall Prevention Wire to the bracket. 5-1. Put a standard anchor nut onto anchor bolt (2). 5-2. Remove the Fall Prevention Wire from the Fall Prevention Angle Clip. 5-3. Insert the anchor bolt (2) through side “1”. 5-4. Fold (manually bend the clip) side “2” down onto side “1” (when folded properly side “1” and side “2” should match). 5-1 5-3 5-2 5-4 5-5 5-6 Side "1" Anchor bolts Side "2" - 3 5-5. Reattach the Fall Prevention Wire to the matched holes of side “1” and “2” of the Fall Prevention Angle Clip. 5-6. Put two standard anchor nuts onto anchor bolt (2). 5-7. Tighten the three nuts to fix the Fall Prevention Angle Clip. 6. Connect the Fall Prevention Wire and put the bracket into the suspended ceiling through the hole. 7. Fix the camera mount bracket to the suspended ceiling by rotating the four ceiling panel screws clockwise. Ceiling support Clockwise Anchor nut Nuts Ceiling panel screws 8. Mount the bracket onto anchor bolt (1). 9. Remove the plate from the camera 11. Connect the fall prevention wire to the mounting base (combination camera camera mounting base. accessory). Plate 10. Attach the camera mounting base to the bracket. Adjust the lock plate so it is in the orientation show in the following illustration, and then tighten the four M4-L 8 Screws (provided). Cables Orientation of installation Lock plateM4-L8 Bracket Note: Tug on the Fall Prevention Wire to make sure it is secure. 12. Install the camera to the camera mounting base. *The top case is not shown in the following illustration. 15° Rotate Camera Base unit - 4 13. Secure the camera to the lock plate. Securing the camera After installing the camera, move the lock plate in the direction of the arrow, and secure it with a screw. Make sure that the camera cannot come loose after tightening the screws. Lock Locked Lock Move the upper lock to secure the camera Move the lock plate in the direction of the arrow LockLock Problems Lock Lock If the lock plate cannot move into the lock position, then the camera is prob- ably not firmly set. Make sure that the camera is correctly installed. - 5 Uninstalling Loosen the screw, move the lock plate in the direction of the arrow, and then remove the camera. Lock Move the lock plate in the direction of the arrow Lock 14. Mount the decoration cover onto the camera. Align the tabs with the projections of the decoration cover and press up on the camera’s decoration cover. Tabs Match the tabs to the projections Projections 15. Rotate the ...