valutazioni - 5, GPA: 4
(
)
)
|
Facilità d'uso
1. Put the template (accessory) against the wall and mark the positions of fixing screws and hole through which the cables run. If you run the cables through the wall, drill a hole through the wall. 2. Remove the bottom cover from this bracket. q Loosen the fixing screw (unremovable) to be used for cover fall prevention. w Pull down the bottom cover while pressing the marks (shown with a in the drawing) to remove the cover. * Be aware that the inner shell is present in the cover. Wall Mount Bracket Operating Instructions WV-Q150C Model Nos. WV-Q150S Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual. NM0806-1096 3TR004556BAA Printed in Japan Preface This bracket is exclusively designed to mount the network camera, WV-NS202, on a wall. The network camera shall be mounted on this bracket after mounting this bracket on a concrete wall. • WV-Q150C: Clear dome cover • WV-Q150S: Smoked dome cover (approx. 50 % of transmittance) Embedded box Strong panel Concrete Wall box Wall Fixing screw to be used for cover fall prevention Precautions • Refer installation work to the dealer. Installation work requires technique and experiences. Be sure to refer installation work to the dealer to avoid fire, electric shock, injury, or damage to the product. • Use only the specified camera. Failure to observe this may cause a fall of an inappropriate camera resulting in injury or accidents. Mount WV-NS202 on this bracket exclusively. • The measures of protection against a fall of the camera shall be taken. Failure to observe this may cause injury. Be sure to install this bracket-specific safety wire. • Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced. Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera may occur. • The screws and fixation mechanisms shall be tightened securely. Failure to observe this may cause a fall of the camera resulting in injury or accidents. • Periodic inspections shall be conducted. Rust on the metal parts or screws may cause a fall of the camera resulting in injury or accidents. Be sure to consult the dealer for the inspections. • Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury. • Make sure that the installation area is strong enough to hold the total weight of the camera assembly (approx. 1.8 kg {0.4 lbs.}) before installation. • The screws that secure this bracket on a wall are not supplied. Prepare the screws according to the material, structure, strength and other factors of the mounting area and the total weight of objects to be mounted. (4 pieces of M4 screws or 2 pieces of M4 screws and 2 pieces of M6 or M8 anchor bolts) In this case, wood screws and nails should not be used. • Avoid installing in the following locations. • Locations where it may get wet from rain or water splash (not only outdoor) • Locations where a chemical agent is used such as a swimming pool • Locations subject to steam and oil smoke such as a kitchen • Locations near flammable gas or vapor • Locations where radiation or x-ray emissions are produced • Locations subject to strong magnetic field or radio waves • Locations where it may be damaged by briny air such as seashores • Locations where the temperature is not within –10 °C - +50 °C {14 °F - 122 °F}. • Locations subject to vibrations (This product is not designed for on-vehicle use.) • Locations where the temperature may rapidly change such as the peripheral areas of the air outlets of air conditioners or doors facing outside. (In case of installing the camera in such locations, the dome cover may become foggy or condensation may be caused on the cover.) • The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. After tightening the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash. • The pull-out strength of the installation area shall be 40 N {4 kgf} or more per 1 screw. • The protection sheet attached to the dome cover shall be peeled off after installation. Major Operating Controls and Their Functions * If a microphone is used, mount the microphone on the rubber-made microphone stand. Unless the microphone is used, cut the rubber with a nipper or conduct another treatment. Installation Area The drawings below show how to conduct the wiring of this bracket. Template (accessory) Top cover Bottom cover Notch for network cable, monitor output cable, etc. Hole for microphone cable Notch for network cable Dome cover Microphone stand* (To be continued reverse page) 3. Install the inner shell. Slide the covers located on the both lateral sides of the camera and put the inner shell on the camera until the hooks inside the inner shell are held in the holes of the camera (until a click i...