valutazioni - 5, GPA: 4.8
(
)
)
|
Facilità d'uso
780 g (1.72 lb) Approx. 640 g (1.411 lb) Shock resistance specifications Exterior materials: alloyed aluminum, polycarbonate plastics shock absorbing mechanism Estimated shock resistant: 50J (impact strength) * Based on Canon's test method None AC adapter (option) Model PA-V17 Input 100 VAC, 50/60 Hz Output 13 VDC, 1.8 A (max.), temperature -10°C to 35°C, humidity 20 to 85% RH (non-condensing) When combined with the network camera 13 VDC, 1.0A (max.), temperature -10°C to 45°C, humidity 20 to 85% RH (non-condensing) Polarity Black line side (-), white line side (+) Dimensions 58 mm x 118 mm x 25 mm (2.28 in x 4.65 in x 0.98 in) (W x D x H) (excluding projections) Weight Approx. 215 g (0.474 lb) (excluding cables) Recessed Mounting Kit (option) Model SR500-S-VB Type Silver Use environment when combined with the camera Temperature -10 to 50°C, humidity 20 to 85% RH (non-condensing) Dimensions .215mm x 63mm (H) (.8.46 in x 2.48 in (H)) (including brackets) Weight Approx. 395 g (0.871 lb) (including Recessed Mounting Cover and brackets) * Cover only: Approx. 66 g (0.146 lb) Appendix .. The specifications are subject to change without notice for purposes of improvement, etc. 3-5 Input/Output Terminals Input/Output Terminals To connect the camera to an audio input/output device, contact input/output device, AC adapter or external power supply, use dedicated interface cables. All interface cables come with dedicated terminals for connection with the camera. Check the shape of each terminal thoroughly and insert the terminal in the correct direction. VB-C500VD External device I/O terminals Power connection terminal Audio input/output terminals Brown VB-C500D External Device I/O Terminals Two external device input terminals and two external device output terminals are available. VB-C500 Viewer and VK-Lite Viewer can be used to check the conditions of external device inputs and operate external device outputs. ("Operating the External Device Outputs" and "Displaying the External Device Input Status" in Operation Guide). To connect the camera to an external device, use a dedicated I/O interface cable WC500-VB. (.. P. 1-23) The table below lists the colors and functions of spare wires in the I/O interface cable. BlackRedOrangeYellowGreenBlueWhite Input/Output Terminals Input/Output Terminals Type of corresponding terminal 1 Black OUT2_B 2 Brown OUT2_A 3 Red OUT1_B 4 Orange OUT1_A Color of spare wire Type of corresponding terminal 5 Yellow IN2_6 Green IN2_+ 7 Blue IN1_8 White IN1_+ • External Device Input Terminals (IN1, IN2) There are two sets of external device input terminals (IN1, IN2), where each set consists of two terminals. The - terminals are connected to the GND in the camera. Two-wire cables are connected to the + and - terminals to achieve electrical continuity or insulation between the two terminals for notification to the viewer. Note For the sensors and switches to be connected, connect terminals that are electrically isolated from each power supply or GND. • External Device Output Terminals (OUT1, OUT2) There are two sets of external device output terminals (OUT1, OUT2), where each set consists of two terminals. Each terminal set has no polarity. The condition between the two terminals can be switched between connected and disconnected by controlling from the viewer. The output terminals are isolated from the internal circuits of the camera using optical couplers. The loads connected to the output terminals should be used within the following ratings: Ratings between output terminals: Maximum voltage 50 VDC Continuous load current 100 mA max. Appendix 3-7 Input/Output Terminals • Internal Connection Diagram Internal controller External device External device Input terminal: IN1, IN2 Output terminal: OUT1, OUT2 10k.10k.10k.+3.3V + – 0.1.F Tip Applicable wire for external device cable Single wire of AWG No. 28 to 22 Conductor size .0.32 to 0.65 mm (.0.013 to 0.026 in) Strip the cable by approx. 8 to 9 mm (0.31 to 0.35 in) Audio Input/Output Terminals One audio input terminal and one audio output terminal is available. A microphone, speaker with amplifier or other audio input/output device can be connected to the camera to send/receive sound via the viewer. To connect the camera to an audio input/output device, use a dedicated audio interface cable WA500-VB.(.. P. 1-22) Use a .3.5 monaural mini jack connector to connect the audio interface cable and audio input/ output device. Input/Output Terminals • Audio Input, Used as Both LINE IN and MIC IN (Monaural Input) Connects the camera to a microphone. As for audio input of this camera, two types of microphones, LINE IN and MIC IN types, are supported. Note that the camera only has one audio input. Switch the input mode on the Setting page ("Audio Input" in Operation Guide). The factory setting is LINE IN. When LINE IN is selected, a microphone with amplifier can be connected. When MIC IN is selected, a dynamic microphone or capacitor microphone can be connecte...