Log:
valutazioni - , GPA: ( )

Istruzioni per l'uso Chamberlain, Modello WIRELESS ALERT CWV1000

Produttore : Chamberlain
File Size : 1.12 mb
File Nome : 04ca8dfd-0a28-43c4-83f4-a45d99b689f1.pdf

Lingua di insegnamento: enfr

Il documento viene caricato, si prega di attendere
Il documento viene caricato, si prega di attendere

Facilità d'uso


1 2 PIR Motion Sensor Assembly & Test Connect PIR Motion Sensor box to mounting plate with silver screw. Tighten screw until PIR Motion Sensor stays in place when repositioned. A Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) B Ensure batteries do not touch circuit board. Test PIR Motion Sensor by waving hand in front of sensor. Test light should flash after several seconds. Plug in Base Station. Adhere rubber pads to bottom. 4 AA Alkaline batteries (not provided) are optional in case of power failures. A Ensure that Base Station and PIR Motion Sensor are in close proximity to each other. Press and release learn button on Base Station. Buzzer will sound. OPTIONAL A B Secure cover with the two large black screws. B Within 5 seconds, wave hand in front of PIR Motion Sensor. Test light will illuminate and Base Station will activate with static and feedback after several seconds. Programming PIR Motion Sensor to Base Station A B Step 1 Step 2 Step 3 Step 5 Step 6 Advanced Features: Both the PIR Motion Sensor and Step 4 Base Station have relays which can activate other electrical devices. The accessory device will need a separate power supply. NOTE: Output switching capacity is low voltage (24V max, ac or dc). Base Station: The relays can be used to activate louder alarm bells, lights, cameras, or other accessories. PIR Motion Sensor: The relays will only activate when the remote button is pressed on the Base Station. To prevent access to these relays flush mount the PIR Motion Sensor. Troubleshooting The Alert does not function. Check batteries in PIR Motion Sensor. Ensure Base Station has power. Ensure PIR Motion Sensor is programmed to Base Station. The Alert is not getting expected transmission range. Ensure Base Station antenna is vertical and keep PIR Motion Sensor away from trees and metal objects. Ensure Base Station is in clearest possible range of PIR Motion Sensor. The less objects between devices, the longer the range. Base Station is not very loud. Adjust the volume of speaker. An accessory such as a low voltage doorbell, buzzer or light can be attached to the relay switch. The accessory device will need separate power supply. NOTE: Output switching capacity is low voltage (24V max, ac or dc). Static and feedback is heard in Base Station. PIR Motion Sensor is too close to the Base Station. The PIR Motion Sensor is detecting motion only part of the time. To detect cars, it is best to mount PIR Motion Sensor at height of car’s motor and have it between ten and twenty feet from the road. Swivel sensor as needed. The Alert is giving false alarms. Check for moving tree branches or insects in sensor window. PIR motion sensor can also be triggered by light shining directly in sensor window, such as reflected sunlight, or motion in front of a light source. Base Station beeps every ten minutes. If there are two beeps the battery is low in the Base Station. Replace with AA Alkaline batteries or operate it with AC Adapter. If there are three beeps the battery is low in the PIR Motion Sensor. Replace with AA Alkaline batteries. Mount PIR Motion Sensor vertically on solid surface a few feet off the ground and within 1000' of Base Station. Unit should be able to swivel as needed. NOTE: Do not mount PIR Motion Sensor in direct sunlight, near moving tree branches, or in the path of a sprinkler system. 3' - 5' 10' - 20' PIR Motion Sensor Installation Vehicle Alert Installation: For cars, the best mounting position is about 4' high, between 10-20' back, and angled to see the back of car after passing the sensor. Step 7 Troubleshooting The Alert does not function. Check batteries in PIR Motion Sensor. Ensure Base Station has power. Ensure PIR Motion Sensor is programmed to Base Station. The Alert is not getting expected transmission range. Ensure Base Station antenna is vertical and keep PIR Motion Sensor away from trees and metal objects. Ensure Base Station is in clearest possible range of PIR Motion Sensor. The less objects between devices, the longer the range. Base Station is not very loud. Adjust the volume of speaker. An accessory such as a low voltage doorbell, buzzer or light can be attached to the relay switch. The accessory device will need separate power supply. NOTE: Output switching capacity is low voltage (24V max, ac or dc). Static and feedback is heard in Base Station. PIR Motion Sensor is too close to the Base Station. The PIR Motion Sensor is detecting motion only part of the time. To detect cars, it is best to mount PIR Motion Sensor at height of car’s motor and have it between ten and twenty feet from the road. Swivel sensor as needed. The Alert is giving false alarms. Check for moving tree branches or insects in sensor window. PIR motion sensor can also be triggered by light shining directly in sensor window, such as reflected sunlight, or motion in front of a light source. Base Station beeps every ten minutes. If there are two beeps the b...

Questo manuale è adatto anche per i modelli :
Video - WIRELESS ALERT RWV400R (1.12 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie