valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
If the playback VCR is monaural, connect the audio output connector on the playback VCR to the left audio input connector on this VCR. NOTE: If another VCR does not have S-video input/output connectors, use a video cable. 2 2 Load a cassette Insert the cassette to be recorded on into this VCR (for recording). 3 3 Select input location on this VCR L-1 or L-2 — when connecting the device to the audio/video or audio/S-video input connectors on the rear panel. F-1 — when connecting the device to the audio/video or audio/S-video input connectors on the front panel. On the front panel: Press CHANNEL +/–. On the Remote: Press the Number key “0 (AUX)” or TV/VCR CH +/–. NOTES: . When using this VCR as the recording VCR, set the video input terminal setting correctly ( pg. 56). . When using this VCR as the playback VCR for editing, set“DIGITAL R3”to“OFF”( pg. 54). 4 4 Set recording speed Press REC SPEED to set the tape speed. Input Source (Playback device) Selectable Recording Speed (Recording device: This VCR) Analog input D-VHS HS, STD, LS3, LS5 S-VHS/VHS SP, EP 5 5 Select video input terminal Access the “IN/OUT FUNCTION” screen ( pg. 56). When using S VIDEO terminal, set “FRONT AUX F-1” (or “REAR AUX L-1 (or L-2)” if you use the connectors on the rear) to “S-VIDEO”. When using VIDEO terminal, set “FRONT AUX F-1” (or “REAR AUX L-1 (or L-2)” if you use the connectors on the rear) to “VIDEO”. 6 6 Set “PICTURE CONTROL” to “EDIT” Access the “VIDEO FUNCTION” screen ( pg. 54). 7 7 Start playback Press PLAY ( 3 ) on the connected device. NOTE: If the connected device is equipped with a superimpose/OSD disable feature then set it to“OFF” before starting playback. 8 8 Start recording On the front panel: Press REC ( ¶ ). On the Remote: Press REC ( ¶ ) and PLAY ( 3 ) at the same time. To use a Master Edit Control-equipped JVC camcorder 1 Access the “ADDITIONAL” screen ( pg. 57), then set “AV COMPU-LINK” to “OFF” after performing step 6. . The REMOTE PAUSE/AV COMPULINK connector works as a Remote Pause connector when “AV COMPU-LINK” is set to “OFF”. . For details, refer to the camcorder’s instruction manual. 2 Engage the VCR’s recording pause mode. NOTES: . Be sure to select“AUTO”for“PICTURE CONTROL”(or “NORM”when“V. CALIBRATION”is set to“OFF”) after you finish dubbing the tapes ( pg. 54). . It is impossible to perform dubbing properly only with an audio cable. Connect also the video or S-video cable. VCR TV CABLE /DBS 2 3 -2 4 Number keys VCR TV CABLE /DBS 2 3 -2 4 Number keys EN MULTI-BRAND REMOTE CONTROL When programed (set) with a manufacturer’s (brand’s) code, this Remote can perform some of the remote TV Brand control functions of the listed TVs. You can control a JVC TV without setting a brand code. Setting Turn on the TV 1 Turn on the TV using the Power button on the TV TV BRAND NAME BRAND CODE JVC 01, 03 HITACHI 10 MAGNAVOX 02 MITSUBISHI 03 PANASONIC 04, 11 RCA 05 SHARP 06 SONY 07 SAMSUNG 12 SANYO 13 SEARS 13 TOSHIBA 08 ZENITH 09 3 -1,3 4 TV/VCR 4 ENTER 3 -3 TV VOL +/– or its Remote. 2 2 Set remote operation mode Set the VCR/TV/CABLE/DBS selector to “TV”. 3 3 Set TV brand code Follow the example shown below. 1 Press and hold POWER. 2 Press the Number keys to enter your TV’s brand code by referring to the table below. 3 Press STOP ( 7 ), and release POWER. . Once you have set the Remote to operate a TV, you do not have to set it again until you replace the Remote’s batteries. . JVC and PANASONIC have two codes. If the TV does not function with one code, try entering the other. 4 4 Operate TV Press one of the following buttons: POWER, TV/ VCR, TV/VCR CH +/–, (TV Muting), TV VOL +/–, and Number keys. . For some brands, you must press ENTER after having pressed the Number keys to enter a channel number. . To operate the VCR, set the VCR/TV/CABLE/ DBS selector back to “VCR”. NOTES: . Depending on the type of TV, some or all functions cannot be operated using this Remote. . It is impossible to control a TV that does not have a remote sensor. (Ex.) To set Remote to RCA 05: POWER AUX STOP JKL Hold Press in succession Release down EN69 When programed (set) with a manufacturer’s (brand’s) code, this Remote can perform some of the remote Cable Box control functions of the listed cable boxes. If your cable Brand Setting VCR TV CABLE /DBS 2 4 TV/VCR CH +/– ENTER 3 -1,34 3 -33 -2 4 Number keys CABLE BOX BRAND NAME BRAND CODE ARCHER 01, 05, 17 CABLETENNA 01, 17 CABLEVIEW 15, 16, 17, 21, 25 CITIZEN 15, 16, 17, 21, 25 CURTIS 02 DIAMOND 01, 17 GC BRAND 15, 16, 17, 21, 25 GEMINI 15 GENERAL INSTRUMENTS 01, 04, 06, 11, 12, 15, 28 HAMLIN 10, 18, 23 JASCO 15 JERROLD 01, 04, 06, 11, 12, 15, 28 NOVAVISION 02 OAK 07 PANASONIC 13, 14 PULSER 15, 16, 17, 21, 25 RCA 13, 14 REGAL 10, 18, 23 REMBRANDT 01, 16, 17 SAMSUNG 05, 16, 24 SCIENTIFIC ATLANTA 02 SIGMA 07 SL MARX 05, 16, 17, 24, 25 SPRUCER 13, 14 STARGATE 05, 15, 16, 17, 21, 24, 25 TELEVIEW 05, 16, 24 TOCOM 01, 04, 16 UNIKA 01, 17 UNIVERSAL 16, 17, 25 VIDEOWAY 03, 09, 22 ZENITH 03, 09, 22 box ...