Log: Operating Instructions Outdoor Camera Housing WV-7140 Panasonic. Before attempting to connect or operate this product, please read these instruction» completaly. CONTENTS INTRODUCTION ............................................................................1 PRECAUTIONS ............................................................................1 PRECAUTIONS ON INSTALLATION ........................................1 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ......................
ROTA. : The shot image rotates 180 degrees. u Brightness Selection Switch (BRIGHTNESS, AUTO/MANU) AUTO: When this switch is set to the AUTO position, the ELC On/Off Switch (!56 ) and AGC Switch (!) becomes effective. The ELC & AGC of the target level changes by rotating the BRIGHTNESS control knob. MANU: When this switch is set to the MANU position, the video level is adjustable by means of the BRIGHTNESS control knob. Note: Since the variable range of MANU is limited depending on the shot image
Front panel card holders permit each input source to be labeled. For added flexibility, inputs can be Hi-Z looped or 75 ohm terminated (switchable) with BNC connectors. ■ FEATURES • Designed with solid state circuitry for reliability. • Excellent picture reproduction, with minimum crosstalk and low frequency transients. • Electronic, vertical interval switching. • Unterminated, loop-through video inputs; switchable for 75 ohms. • Illuminated, non-lock switch. • Card holder permits each in
The 9-segment screen shows the pictures of channels 1 through 9 in a 3x3 pattern. (D Spot/Multiscreen Selection Button (SPOT/MULTISCREEN) This button is used to select either the Spot output or Multiscreen output. (D Sequence Button (SEQ) This button activates the sequence mode. In this mode, a series of camera pictures is displayed in succession on the monitor screen for the specified duration. (7) Camera Selection Buttons (CAMERA SELECT) These buttons select the camera for live picture o
1 • 2) Th#»*»» pr>ftn .vcect e-t'w# *deo Signal from me VCEO Oo' port cn toe Cam«#-» l»u * Soa-d 0» ton Cam«»* Co» t .»go (M<< NT) of fro*" too VlO€OOUT ooronif-e Cross 3o«nt next P irtoer (vt Pom .».j*»(MX .W Pm No Designation Pin No Designation 25 VIDEO 1 13 Ground 24 VIDEO 2 12 Ground 23 VIDEO 3 11 (Hound 22 VIDEO 4 10 Ground 21 VIDEO 5 9 Ground 20 VIDEO 6 8 Ground 19 VIDEO 7 7 Ground 18 VIDEO 8 6 Ground 17 Not Used 5 Ground 16 Not Useo 4 QrouxJ 16 No- Used 3 Ground 14
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The serial number of this product may be found on the left of the unit. You should note the senal number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No. _ Serial No.-- WARNING: To reduce the risk of fire or electric shock, do not expose this
HOLD) This control is used to lock the horizontal position of the picture. 5. Vertical Hold Control (V. HOLD) This control is used to lock the vertical position of the picture. 6. Height Control (HEIGHT) This control is used to adjust the height of the picture. 7. Bright Control (BRIGHT) Turn this control clockwise to increase the picture brightness. Turn this control counterclockwise to decrease the picture brightness. 8. Vertical Linearity Control (V. LIN) This control is used to cor
If the ring is rotated by force, the inner lens or CCD image sensor may be damaged. -12- Tighten the screws on the flange-back adjusting ring. INSTALLATION OF CAMERA • Mounting from the bottom This camera is designed to be mounted from the bottom, as shown below. The mounting hole is a standard photographic pan-head screw size (1/4" -20).
This setup can be only made when the multiplexed vertical drive (VD2) pulse is not supplied to the camera. f - ** SET OP ** CAMERA ID OFF * ALC/ELC AliC * SHUTTER OFF AGC ON SENS UP OFF SYNC LL_] 4- WIDE D-RANGE OFF MOTION DET OFF END SET tip ENABLE V Fig. 52 * After confirming that the cursor is on the 'LL‘ position, press the Set Switch (9) on the rear panel. The following vertical phase adjustment menu is then displayed on the monitor. * 4 > SYNC ** V PHASE COARSE I'ni’EEF»
This input has priority when the VIDEO IN and S-VIDEO IN connectors are connected to an outboard device. ADVANCED CONTROL OPERATION • Displaying the Setup Display 1. Turn on the Power Switch of the Monitor. 2. Press the Control Panel Cover to open for access to the control buttons on the Control Panel. 3. Press the MENU button, the setup display shown below appears on the monitor screen. It will disappear automatically when no operation takes place for about 3 seconds. B RIG HT] .........
