valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
With knot to right side, place smaller log piece (#5) over the pin on the left side of the middle log. The smaller log will rest on front log against the "knot" on the left. See Figure 27. 6. Place lava rock around base of heater if desired. Do not put lava rock on logs on burner. Recess INSTALLATION Installing Logs (Cont.) 107124-01E Forr morre iinfforrmattiion,, viisiitt 16 Dual Burner Biltmore Split Oak Models WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury. INSTALLATION Continued CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to HI, check to see if flames contact any log. If so, reposition logs according to the log installation instructions in this manual. Flames contacting logs will create soot. Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater. 1. Place the front log (#1) on the grate fingers. Make sure the front log rests firmly between the grate fingers and the grate base (see Figure 28). 2. Place the base of the middle log (#2) in the U-shaped slots of the grate base. The cutout on the right of the middle log should fit over the burner (see Figure 29). Make sure the front of the middle log is resting on the tabs of the grate base. 3. Locate pins on the bottom of back log (#3). Slide these pins into the holes in the grate base behind the burner (see Figure 30). 4. Locate holes on the bottom of crossover log (#4). Slide front hole onto the left pin (CCL3924PT or CCL3930PTA) or middle pin (CCL3018P or CCL3018PT) on the middle log (#2) and the pin on the back log (#3). See Figure 31 for placement. Figure 28 - Installing Front Log (#1) (CCL3930PTA Shown) Front Log (#1) Grate Fingers Grate Base Figure 29 - Installing Middle Log (#2) (CCL3930PTA Shown) Figure 30 - Installing Rear Log (#3) (CCL3930PTA Shown) Figure 31 - Installing Crossover Log (#4) (CCL3930PTA Shown) Middle Log (#2) Tab Burner U-Shaped Slot Hole in Grate Base Pins Burner Log #2 Log #3 Pins Log #4 INSTALLATION Installing Logs (Cont.) 107124-01E Forr morre iinfforrmattiion,, viisiitt 1177 INSTALLATION Continued 7 6 Figure 34 - Installing Crossover Log (#6) (CCL3930PTA Shown) Figure 35 - Installing Crossover Log (#7) (Model CCL3930PTA Only) Pins Log #2 Front Log (#1) Middle Log (#2) Crossover Log (#6) Holes Pins 5. For CCL3924PT and CCL3930PTA Only: Locate pin and hole on the bottom of crossover log (#5). Slide the pin into the hole located in crossover log (#4). Slide the hole onto the pin on front log (#1). See Figure 32. For CCL3018P and CCL3018PT Only: Locate holes on the bottom of crossover log (#5). Slide the holes over the left pins on middle log (#2) and front log (#1). See Figure 33. 6. Locate holes on the bottom of crossover log (#6). Slide these holes onto the right pins located in middle log (#2) and front log (#1). See Figure 34. 7. For CCL3930PTA only: Locate holes on the bottom of crossover log (#7). Slide onto the pins located in crossover log (#6) and middle log (#2). See Figure 35. 8. Add lava rock around base of heater if desired. Do not place any lava rock on logs or burner. Figure 32 - Installing Crossover Log (#5) (CCL3930PTA Shown) Crossover Log (#4) Front Log (#1) Crossover Log (#4) Front Log (#1) Figure 33 - Installing Crossover Log (#5) (CCL3018P and CCL3018PT Only) INSTALLATION Installing Logs (Cont.) 107124-01E Forr morre iinfforrmattiion,, viisiitt 18 INSTALLATION Installing Logs (Cont.) Single Burner Seasonal Oak Models WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury. The Seasonal Oak Log Set is a reversible log set. This means that the two bottom logs may be turned to face either direction. The top log, however, must remain in the same position. Do not modify logs. Only use logs supplied with heater. 1. Place the back log onto the back of the base assembly. Make sure log sits forward against the two posts in front of log (see Figure 36). This log may be turned to face either direction. 2. Place front log onto grate on front of base assembly. The log will fit down between grate fingers and posts on front of base assembly (see Figure 37). This log may be turned to face either direction. 3. Place the crossover log on top of the back log and front log making sure pins are inserted into holes on top of logs 1 and 2 (see Figure 38). This log must be placed as shown in Figure 38 or the pins will not seat into holes. 4. Add lava rock around base of heater if desired. Do not put lava rock on logs or burner. Figure 36 - Installing...