valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
*Available from: American National Standards Institute, Inc. 1430 Broadway New York, NY 10018 National Fire Protection Association, Inc. Batterymarch Park Quincy, MA 02269 Note:Do not remove Control Knob Lighting and Warning UNPACKING WARNING: Do not remove the metal data plates attached to the heater assembly. The data plates contain important warranty information. 1. Remove heater from carton. 2. Remove all protective packaging applied to heater for shipment. 3. Make sure your heater includes two hardware packets. 4. Check heater for any shipping damage. If heater is damaged, promptly inform dealer where you bought heater. PRODUCT FEATURES SAFETY PILOT This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room heaters. The ODS/pilot shuts off the heater if there is not enough fresh air. PIEZO IGNITION SYSTEM This heater has a piezo ignitor. This system requires no matches, batteries, or other sources to light heater. THERMOSTATIC HEAT CONTROL This heater has a thermostat sensing bulb and a control valve. This results in the greatest heater comfort. This can also result in lower gas bills. 3 VENT-FREE PROPANE/LP HEATER ASSEMBLY ASSEMBLING HEATER Tools Required: • Phillips Screwdriver • 5/16" hex wrench • Slotted screwdriver Removing Front Panel Of Heater 1. Remove two screws near bottom corners of front panel with Phillips screwdriver. 2. Pull bottom of front panel forward, then down (see Figure 2) . Installing Log Note:For easier installation, lay heater on its back. 1. Remove log from inside top of heater. Discard protective packaging. 2. Attach ignitor cable to piezo ignitor (see Figure 3). 3. With Phillips screwdriver, remove four screws holding screen in place. Remove screen. 4. Gently slide log between log retaining brackets on deflector assembly (see Figure 4). The log should fit firmly against bottom of log retaining brackets. 5. Reattach screen using four screws removed in step 3. WARNING: Always have burner shield and screen in place before operating heater. This prevents excessive temperatures on heater surfaces. Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury. Figure 2 - Removing Front Panel of Heater Figure 4 - Assembling Heater Attaching Brass Front Trim to Front Panel 1. Locate brass front trim in brass trim package. 2. Slide the head of two truss-head screws from hardware packet into each end of brass front trim (see Figure 5). 3. Line up screws with holes in front panel (see Figure 4). Insert screws in holes. Attach nuts from inside of front panel. Tighten with wrench. Piezo Ignitor Ignitor Cable Figure 3 - Attaching Ignitor Cable to Piezo Ignitor Heater Cabinet Brass Front Trim Front Panel Nut Screw Figure 5 - Attaching Brass Front Trim to Front Panel Truss-Head Burner Shield Screen Front Panel Deflector Log Retaining Brackets Log Truss Head Screw Brass Front Trim Screw Screw Nut 4 OWNER’S MANUAL ASSEMBLY Continued Assembling and Attaching Brass Trim 1. Remove packaging from three remaining pieces of brass trim. 2. Locate four brass screws, two adjusting plates with set screws, and two shims in the hardware packet. 3. Align shim under adjusting plate as shown in Figure 6. 4. Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 6). 5. Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 6). 6. While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver. 7. Repeat steps 1 through 6 for other side. 8. Place the assembled trim on front of heater cabinet. Attach on top and sides with four brass screws included in hardware package (see Figure 7). 9. Reattach front panel to heater if you are going to mount the heater to the base. Do not reattach front panel at this time if you are going to mount heater to wall. Set Screws Top Side Adjusting Shim Brass Brass Plate Trim Trim Mitered Edge Slot Slot Figure 6 - Assembling Brass Trim Assembled Brass Trim Screws Figure 7 - Attaching Brass Trim to Heater AIR FOR COMBUSTION AND VENTILATION WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home. Today’s homes are built more energy efficient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible. While it is good to make your home energy efficient, your home needs to breathe. Fresh air must ent...
Questo manuale è adatto anche per i modelli :scaldabagno - 000 to 30 (932.39 kb)